On any public road.

Inform you of the speed limit applicable on this road. The restriction applies from the sign.

Do not exceed the speed indicated by this sign.

Overview The Speed Limit Sign in South Africa is a regulatory prohibition sign used on all public roads to indicate the maximum legal speed allowed. It informs drivers of the speed restriction that applies from the point where the sign is placed and continues until changed by another sign. What the Sign Means When a driver encounters this sign, it means they must not exceed the indicated speed limit from that point onward. The limit applies to all vehicles unless a different speed is later posted. The key rule is: do not drive faster than the speed shown on the sign. Driver Responsibilities Observe and obey the posted speed limit immediately Adjust speed according to road, traffic, and weather conditions Reduce speed in built-up, school, or hazardous areas Stay alert for updated speed limit changes along the route Where You Will See This Sign This sign is commonly found: On all public roads, highways, and urban streets At entrances to towns, cities, or residential areas Near schools, construction zones, and hazardous areas On rural roads and national highways Purpose of the Sign The purpose of the Speed Limit Sign is to regulate traffic speed in order to improve road safety, reduce accidents, and protect all road users, including pedestrians and cyclists. Common Mistakes to Avoid Continuing at a higher speed after passing the sign Ignoring lower limits in residential or school zones Assuming speed limits are the same on all roads Not adjusting speed for weather or road conditions Safety Tips Always check for speed limit signs when entering new roads Drive below the limit in poor visibility or wet conditions Slow down in built-up or pedestrian-heavy areas Be alert for sudden speed limit changes in construction zones Penalties for Ignoring the Sign Exceeding the posted speed limit is a traffic offence and may result in: Fines Demerit points under traffic laws Licence suspension for repeated offences Increased risk of serious or fatal accidents Summary The Speed Limit Sign in South Africa sets the legal maximum driving speed on a road. It is essential for maintaining safe traffic flow and reducing road accidents.

On any public road.

To prevent certain heavy vehicles from using a road or part of a road.

If the GVM or GCM of your vehicle exceeds the mass indicated in tons, use another road or part of the road, which is not indicated by this sign. If your vehicle’s GVM or GCM is less than the indicated mass in tons, you may use this road.

Overview The Mass Limit Sign in South Africa is a regulatory prohibition sign used on public roads to restrict vehicles that exceed a specified weight. It is primarily applied to protect road surfaces, bridges, and infrastructure from damage caused by heavy vehicles. What the Sign Means When a driver encounters this sign, it means that vehicles exceeding the indicated mass (weight limit) are not allowed to use the road or section beyond the sign. Only vehicles within the permitted weight range may proceed. The key rule is: do not enter if your vehicle exceeds the stated mass limit. Driver Responsibilities Check your vehicle’s gross vehicle mass (GVM) before entering restricted roads Use alternative routes if your vehicle exceeds the limit Follow all additional axle load or bridge restriction signs Ensure compliance when transporting heavy cargo Where You Will See This Sign This sign is commonly found: On rural and secondary roads with weaker pavement structures At bridge entrances with weight restrictions In residential or low-capacity road networks Near construction zones or temporary road diversions Purpose of the Sign The purpose of the Mass Limit Sign is to protect road infrastructure from excessive wear and structural damage. It also improves safety by preventing heavy vehicles from operating in areas not designed to support their weight. Common Mistakes to Avoid Entering restricted roads without checking vehicle weight Assuming all roads can support heavy loads Ignoring additional axle load restrictions Using restricted routes as shortcuts for freight transport Safety Tips Always know your vehicle’s loaded weight before travel Plan routes using designated heavy vehicle corridors Be cautious of old bridges or narrow rural roads Follow detour signage for heavy vehicles Penalties for Ignoring the Sign Ignoring a Mass Limit Sign is a traffic offence and may result in: Fines Towing or forced removal from restricted roads Demerit points (where applicable) Liability for damage to road infrastructure Summary The Mass Limit Sign in South Africa restricts heavy vehicles from entering roads that cannot safely support their weight. It helps preserve infrastructure and ensures safer travel conditions for all road users.

On any public road.

To prohibit certain heavy vehicles from using the road.

If the axle mass of any of your vehicle’s axles exceeds the indicated mass in tons, use another road or part of the road not indicated by this sign.

Overview The Axle Mass Load Limit Sign in South Africa is a regulatory prohibition sign used on public roads to restrict vehicles based on the maximum weight allowed on a single axle. It is designed to protect road surfaces, bridges, and structures from damage caused by concentrated heavy loads. What the Sign Means When a driver encounters this sign, it means that no vehicle with an axle load exceeding the stated limit is allowed to use the road or section beyond the sign. Even if the total vehicle weight is acceptable, exceeding the axle limit is not permitted. The key rule is: do not proceed if any axle exceeds the permitted weight limit. Driver Responsibilities Check your vehicle’s axle loads before entering restricted roads Distribute cargo properly to avoid axle overload Use designated heavy vehicle routes where required Comply with all additional bridge and mass restriction signs Where You Will See This Sign This sign is commonly found: On bridges with structural weight limitations On rural or aging road infrastructure In industrial or construction zones Along routes not designed for heavy freight traffic Purpose of the Sign The purpose of the Axle Mass Load Limit Sign is to prevent damage caused by excessive pressure on specific points of the road surface. It helps extend road lifespan and ensures safe passage by controlling heavy axle loads. Common Mistakes to Avoid Ignoring axle-specific weight restrictions Assuming total vehicle weight is the only limitation Overloading individual axles with uneven cargo distribution Using restricted roads as shortcuts for heavy transport Safety Tips Always check both total mass and axle load limits before travel Load vehicles evenly to distribute weight correctly Use approved freight routes for heavy cargo transport Be alert for additional weight restriction signage on bridges Penalties for Ignoring the Sign Ignoring an Axle Mass Load Limit Sign is a traffic offence and may result in: Fines Towing or removal of overloaded vehicles Demerit points (where applicable) Liability for infrastructure damage Summary The Axle Mass Load Limit Sign in South Africa restricts vehicles based on the weight carried on each axle rather than total vehicle weight. It plays a vital role in protecting roads and bridges from structural damage caused by concentrated heavy loads.

On any public road.

To warn you against a height restriction ahead.

If your vehicle (or load) is higher than the indicated height in metres, another road not indicated by this sign, must be used.

Overview The Height Limit Sign in South Africa is a regulatory prohibition sign used on public roads to warn drivers of a maximum vehicle height restriction ahead. It is especially important for preventing collisions between tall vehicles and overhead structures such as bridges, tunnels, and overhead cables. What the Sign Means When a driver encounters this sign, it means that vehicles exceeding the indicated height are not allowed to proceed beyond that point. Drivers must ensure their vehicle can safely pass under the upcoming restriction. The key rule is: do not proceed if your vehicle exceeds the maximum height shown. Driver Responsibilities Know your vehicle’s total height (including cargo or roof loads) Check clearance restrictions before entering low bridges or tunnels Use alternative routes if your vehicle is too tall Follow all additional warning and detour signs Where You Will See This Sign This sign is commonly found: Before low bridges and overpasses At tunnel entrances In urban areas with overhead structures or cables Near parking garages and restricted-access zones Purpose of the Sign The purpose of the Height Limit Sign is to prevent accidents involving tall vehicles striking overhead obstacles. It protects both road users and infrastructure by ensuring vehicles with excessive height take appropriate alternative routes. Common Mistakes to Avoid Ignoring roof loads or cargo that increase vehicle height Entering tunnels or bridges without checking clearance Assuming all trucks or buses can pass safely Relying only on GPS without observing road signs Safety Tips Always confirm your vehicle height before starting a trip Look for advance warning signs before low-clearance structures Drive slowly when approaching height-restricted areas Use designated truck or high-clearance routes when needed Penalties for Ignoring the Sign Ignoring a Height Limit Sign is a traffic offence and may result in: Fines Vehicle damage liability Towing or removal from restricted areas Demerit points (where applicable) Summary The Height Limit Sign in South Africa warns drivers of low-clearance restrictions ahead. It is essential for preventing collisions with bridges, tunnels, and overhead structures by ensuring only suitably sized vehicles proceed.

On any public road, especially in mountainous areas.

To prohibit long vehicles from using a road where such a vehicle will not be able to negotiate a curve or will turn in such a manner that it will disrupt or endanger other traffic.

If applicable, take an alternative route.

Overview The Length Limit Sign in South Africa is a regulatory prohibition sign used on public roads, especially on mountainous routes, narrow roads, and sharp-curved sections. It restricts the use of roads by vehicles that exceed a specified length to ensure safe navigation and prevent obstruction or accidents. What the Sign Means When a driver encounters this sign, it means vehicles longer than the indicated limit are not permitted to proceed beyond that point. This is because long vehicles may struggle to safely negotiate sharp bends, narrow lanes, or confined road layouts. The key rule is: do not enter if your vehicle exceeds the maximum permitted length. Driver Responsibilities Know the total length of your vehicle combination (including trailers) Avoid restricted mountain or narrow road routes if oversized Use designated freight or alternative routes when necessary Check advance warning signs for length restrictions Where You Will See This Sign This sign is commonly found: In mountainous areas with sharp bends On narrow rural or secondary roads In historic towns with tight street layouts On bridges or roads with limited turning space Purpose of the Sign The purpose of the Length Limit Sign is to prevent long vehicles from entering roads where they cannot safely manoeuvre. It helps reduce the risk of traffic obstruction, accidents, and road damage caused by large turning movements. Common Mistakes to Avoid Ignoring trailer length when calculating total vehicle size Entering narrow or mountainous roads without checking restrictions Using restricted roads as shortcuts for heavy transport Assuming all roads are suitable for articulated vehicles Safety Tips Always know your full vehicle and trailer length before travel Plan routes suitable for long or articulated vehicles Drive slowly on winding or narrow roads Be alert for advance warning signs before restrictions Penalties for Ignoring the Sign Ignoring a Length Limit Sign is a traffic offence and may result in: Fines Towing or forced removal from restricted roads Demerit points (where applicable) Liability for traffic obstruction or accidents Summary The Length Limit Sign in South Africa restricts long vehicles from entering roads where they cannot safely turn or pass. It is essential for preventing congestion, collisions, and navigation difficulties on narrow or mountainous routes.

On any public road usually near hospitals, churches and homes for the aged.

To prohibit noise.

If the noise level of your vehicle is high, you may not proceed past the sign, and for 100 metres after passing the sign, the vehicle’s hooter may not be used.

Overview The Excessive Noise Prohibition Sign in South Africa is a regulatory prohibition sign used in sensitive areas where noise must be strictly controlled. It is commonly placed near hospitals, churches, schools, and residential areas such as homes for the aged. What the Sign Means When a driver encounters this sign, it means that making excessive noise is prohibited in the designated area. This includes unnecessary hooting, loud engines, or any behaviour that creates disturbing noise levels. The key rule is: keep noise levels to a minimum at all times. Driver Responsibilities Avoid unnecessary hooting or loud use of the horn Keep engine noise low, especially in residential or sensitive zones Avoid loud music or sound systems while driving Drive smoothly without rapid acceleration or harsh braking Be respectful of nearby pedestrians and residents Where You Will See This Sign This sign is commonly found: Near hospitals and medical facilities Outside churches and places of worship In residential neighbourhoods and retirement homes Near schools and learning institutions Purpose of the Sign The purpose of the Excessive Noise Prohibition Sign is to protect public health, comfort, and concentration in sensitive environments. It helps reduce noise pollution and ensures peaceful conditions for patients, residents, and worshippers. Common Mistakes to Avoid Using the horn unnecessarily in quiet zones Revving the engine or accelerating loudly Playing loud music in residential areas Ignoring signage in hospital or school zones Safety Tips Drive slowly and smoothly in quiet zones Anticipate traffic flow to avoid sudden braking or hooting Keep vehicle maintenance up to reduce engine noise Be especially cautious near pedestrians and vulnerable road users Penalties for Ignoring the Sign Ignoring an Excessive Noise Prohibition Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Possible municipal noise violation penalties Complaints or enforcement action in sensitive areas Summary The Excessive Noise Prohibition Sign in South Africa restricts unnecessary noise in sensitive areas such as hospitals, churches, and residential zones. It promotes a quieter, safer, and more respectful environment for all road users and nearby communities.

On any public road.

To prohibit pedestrians and stationary vehicles.

No pedestrian may attempt to be picked up by a passing vehicle. A driver of a vehicle may not pick up passengers for the next 500m.

Overview The Hitch-Hiking Prohibited Sign in South Africa is a regulatory prohibition sign used on public roads to control unsafe roadside behaviour. It indicates that hitch-hiking and soliciting lifts from passing vehicles is not allowed in the marked area. What the Sign Means When a driver or pedestrian encounters this sign, it means that stopping on the roadside to request rides is strictly prohibited. It also restricts pedestrians from standing in unsafe positions that may interfere with traffic flow. The key rule is: no hitch-hiking or roadside vehicle solicitation allowed. Pedestrian Responsibilities Do not stand on the roadway or verge attempting to stop vehicles Avoid placing yourself in dangerous traffic areas Use designated transport stops or facilities instead Follow all pedestrian safety rules in the area Driver Responsibilities Do not stop to pick up hitch-hikers in prohibited zones Remain alert for pedestrians near the roadside Continue driving safely without unnecessary stops Report unsafe roadside behaviour where required Where You Will See This Sign This sign is commonly found: On highways and high-speed roads Near interchanges and busy intersections In urban and peri-urban areas with heavy traffic flow In zones where stopping on the roadside is dangerous Purpose of the Sign The purpose of the Hitch-Hiking Prohibited Sign is to improve road safety by preventing pedestrians from standing in dangerous traffic areas. It also helps maintain smooth traffic flow by reducing unexpected stops and roadside congestion. Common Mistakes to Avoid Standing on highways attempting to flag down vehicles Stopping in unsafe or restricted roadside areas Picking up hitch-hikers in prohibited zones Ignoring designated public transport facilities Safety Tips Always use official taxi ranks or bus stops Avoid walking or standing near high-speed traffic Plan travel using safe and legal transport options Stay visible and away from moving traffic lanes Penalties for Ignoring the Sign Ignoring a Hitch-Hiking Prohibited Sign is a traffic offence and may result in: Fines for pedestrians or drivers Demerit points (where applicable) Enforcement action for unsafe roadside behaviour Increased risk of accidents or legal liability Summary The Hitch-Hiking Prohibited Sign in South Africa prohibits roadside hitch-hiking and unsafe pedestrian stopping on public roads. It is intended to improve safety and reduce risks for both pedestrians and motorists.

On any public road where it is necessary to close the road for general traffic.

To prohibit drivers without special authorisation from entering a certain road or section of a road.

Do not proceed past the sign or enter the road without special permission.

Overview The Unauthorized Vehicles Prohibited Sign in South Africa is a regulatory prohibition sign used to restrict access to specific roads or sections of roads. It is typically placed where only approved or specially authorised vehicles are permitted to enter. What the Sign Means When a driver encounters this sign, it means that entry is not allowed unless the vehicle has official permission or authorisation. All general traffic must stop and use an alternative route. The key rule is: only authorised vehicles may proceed—general traffic is prohibited. Driver Responsibilities Do not enter the restricted area without valid authorisation Follow detour or diversion signs where provided Respect road closures and security controls Be alert for security or traffic enforcement personnel Ensure compliance with permits if access is required Where You Will See This Sign This sign is commonly found: At road closures for construction or maintenance Near secure facilities or restricted government areas In private or controlled access zones During special events or emergency operations Purpose of the Sign The purpose of the Unauthorized Vehicles Prohibited Sign is to control access to sensitive or restricted road sections. It ensures safety, security, and proper traffic management in areas where general access is not permitted. Common Mistakes to Avoid Entering a closed road without checking access permissions Ignoring diversion or detour instructions Assuming short closures do not apply to all vehicles Attempting to bypass barriers or checkpoints Safety Tips Always observe road closure signage early Follow official detour routes without hesitation Plan alternative travel routes in advance if possible Comply with instructions from traffic or security officials Penalties for Ignoring the Sign Ignoring an Unauthorized Vehicles Prohibited Sign is a serious offence and may result in: Fines Demerit points (where applicable) Vehicle removal or towing Legal action in restricted or secure areas Summary The Unauthorized Vehicles Prohibited Sign in South Africa restricts access to specific roads to only authorised vehicles. It ensures safety, security, and proper control of traffic in closed or restricted areas.

On any public road before a junction.

To prohibit vehicles from turning at an intersection.

Do not turn left ahead at the next junction.

Overview The Left Turn Ahead Prohibited Sign in South Africa is a regulatory prohibition sign used before intersections. It informs drivers that they are not allowed to make a left turn at the upcoming junction. What the Sign Means When a driver sees this sign, it means that turning left at the next intersection is strictly prohibited. Drivers must continue straight, turn right (if permitted), or use an alternative route as directed by signage. The key rule is: no left turn allowed at the upcoming junction. Driver Responsibilities Do not attempt to turn left at the intersection Observe alternative route signs or detours Plan lane positioning early to avoid last-minute errors Follow all road markings and traffic signals Remain alert for additional restriction signs at the junction Where You Will See This Sign This sign is commonly found: Before busy urban intersections At junctions with restricted traffic flow Near roadworks or temporary traffic diversions In areas where left turns may cause congestion or safety risks Purpose of the Sign The purpose of the Left Turn Ahead Prohibited Sign is to improve traffic flow and safety by preventing dangerous or disruptive turning movements at intersections. It helps reduce congestion and minimise collision risks at busy junctions. Common Mistakes to Avoid Attempting a prohibited left turn at the intersection Ignoring advance warning signage Changing lanes too late before the junction Failing to follow designated detour routes Safety Tips Always read signage well before reaching intersections Position your vehicle in the correct lane early Use GPS or road maps to anticipate restricted turns Slow down when approaching complex junctions Penalties for Ignoring the Sign Disobeying a Left Turn Ahead Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of accidents at intersections Possible obstruction of traffic flow Summary The Left Turn Ahead Prohibited Sign in South Africa prevents drivers from turning left at the next intersection. It is used to manage traffic flow, improve safety, and reduce congestion at busy junctions.

On any public road before a junction.

To prohibit vehicles from turning at an intersection.

Do not turn right ahead at the next junction.

Overview The Right Turn Ahead Prohibited Sign in South Africa is a regulatory prohibition sign placed before intersections. It informs drivers that making a right turn at the upcoming junction is not allowed. What the Sign Means When a driver sees this sign, it means they are prohibited from turning right at the next intersection. Drivers must continue straight, turn left if permitted, or follow an alternative route indicated by other road signs. The key rule is: no right turn allowed at the upcoming junction. Driver Responsibilities Do not attempt to turn right at the intersection Follow all detour or alternative route instructions Position your vehicle in the correct lane early Observe traffic signals and road markings carefully Plan your route in advance to avoid last-minute lane changes Where You Will See This Sign This sign is commonly found: At busy urban intersections Near roadworks or temporary traffic diversions In areas with high pedestrian or traffic conflict risk Where right turns may disrupt traffic flow or safety Purpose of the Sign The purpose of the Right Turn Ahead Prohibited Sign is to improve traffic safety and efficiency by preventing right-turn movements that may cause congestion or accidents at intersections. Common Mistakes to Avoid Attempting a prohibited right turn at the junction Ignoring advance warning signage Entering the wrong lane too late before the intersection Failing to follow designated alternative routes Safety Tips Always check signage well before reaching intersections Move into the correct lane early to avoid confusion Reduce speed when approaching restricted junctions Use navigation tools to anticipate turn restrictions Penalties for Ignoring the Sign Ignoring a Right Turn Ahead Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions at intersections Traffic disruption or obstruction penalties Summary The Right Turn Ahead Prohibited Sign in South Africa prevents drivers from turning right at the upcoming intersection. It is used to manage traffic flow, reduce congestion, and improve safety at busy junctions.

At intersections on any public road.

To prohibit traffic from turning left or right.

You may not turn left at this sign.

Overview The Left Turn Prohibited Sign in South Africa is a regulatory prohibition sign used at intersections on public roads. It indicates that drivers are not allowed to turn left at the designated junction. What the Sign Means When a driver encounters this sign, it means that a left turn at the upcoming intersection is strictly prohibited. Depending on additional signage, other movements such as going straight or turning right may still be allowed. The key rule is: no left turn allowed at this intersection. Driver Responsibilities Do not attempt to turn left at the intersection Observe and follow alternative route signage Position your vehicle in the correct lane early Follow traffic signals and road markings carefully Plan your route ahead of time to avoid confusion Where You Will See This Sign This sign is commonly found: At busy urban intersections In areas with high pedestrian traffic Near roadworks or temporary diversions Where left turns may cause congestion or safety risks Purpose of the Sign The purpose of the Left Turn Prohibited Sign is to improve traffic flow and safety by preventing left-turn movements that could disrupt traffic or create collision risks at intersections. Common Mistakes to Avoid Attempting a prohibited left turn at the intersection Ignoring advance warning signage Entering the wrong lane too late Failing to follow designated detours or alternative routes Safety Tips Always observe signs well before reaching intersections Choose the correct lane early to avoid last-minute changes Reduce speed when approaching restricted junctions Use navigation tools to anticipate route restrictions Penalties for Ignoring the Sign Ignoring a Left Turn Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions at intersections Traffic disruption or obstruction penalties Summary The Left Turn Prohibited Sign in South Africa prevents vehicles from turning left at specific intersections. It helps regulate traffic flow, reduce congestion, and improve road safety in busy or sensitive junctions.

At intersections on any public road.

To prohibit traffic from turning left or right.

You may not turn right at this sign.

Overview The Right Turn Prohibited Sign in South Africa is a regulatory prohibition sign used at intersections on public roads. It indicates that drivers are not allowed to turn right at the designated junction. What the Sign Means When a driver encounters this sign, it means a right turn at the upcoming intersection is strictly prohibited. Depending on other signage, drivers may still be allowed to proceed straight or turn left. The key rule is: no right turn allowed at this intersection. Driver Responsibilities Do not attempt to turn right at the intersection Follow any indicated detour or alternative route Position your vehicle in the correct lane early Observe traffic signals and road markings carefully Plan your route in advance to avoid last-minute lane changes Where You Will See This Sign This sign is commonly found: At busy city intersections Near roadworks or temporary traffic diversions In areas with high traffic congestion Where right turns may create safety risks or delays Purpose of the Sign The purpose of the Right Turn Prohibited Sign is to improve road safety and traffic flow by preventing right-turn movements that could cause congestion or increase the risk of collisions at intersections. Common Mistakes to Avoid Attempting a prohibited right turn at the junction Ignoring advance warning signs Entering the wrong lane too late Failing to follow alternative routes Safety Tips Always read signage before reaching intersections Move into the correct lane early Slow down when approaching restricted junctions Use navigation tools to anticipate turn restrictions Penalties for Ignoring the Sign Ignoring a Right Turn Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of intersection collisions Traffic obstruction penalties Summary The Right Turn Prohibited Sign in South Africa prevents vehicles from turning right at specific intersections. It is used to regulate traffic flow, reduce congestion, and improve safety at busy or high-risk junctions.

On a public road before or on the far side of an intersection.

To vehicles from turning around so that it faces the opposite direction.

Do not make a U-turn where this sign is displayed.

Overview The U-turn Prohibited Sign in South Africa is a regulatory prohibition sign used on public roads near intersections or junctions. It indicates that drivers are not allowed to make a U-turn at the designated location. What the Sign Means When a driver sees this sign, it means turning the vehicle around to face the opposite direction is strictly prohibited at or near that point on the road. This restriction is usually in place to maintain traffic flow and improve safety at busy or limited-visibility intersections. The key rule is: no U-turns allowed at the specified location. Driver Responsibilities Do not attempt a U-turn where the sign is displayed Continue driving to the next permitted turning point Observe all intersection and lane markings carefully Plan your route in advance to avoid unnecessary turning Follow alternative route signage where provided Where You Will See This Sign This sign is commonly found: At or near busy intersections On roads with limited visibility or high traffic volumes In urban areas to prevent congestion Near roadworks or controlled traffic zones Purpose of the Sign The purpose of the U-turn Prohibited Sign is to improve road safety and traffic efficiency by preventing turning movements that may disrupt traffic flow or create collision risks. Common Mistakes to Avoid Attempting a U-turn despite the restriction Confusing nearby intersections as permitted turning points Blocking traffic while trying to reverse or turn around Ignoring advance warning signage Safety Tips Always check for U-turn restrictions before approaching intersections Plan your route to avoid needing to turn back Use designated turning points instead of illegal manoeuvres Slow down and observe all road signs carefully Penalties for Ignoring the Sign Ignoring a U-turn Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions at intersections Traffic obstruction or unsafe driving penalties Summary The U-turn Prohibited Sign in South Africa prevents drivers from turning their vehicles around at specific locations. It is used to improve safety, reduce congestion, and maintain smooth traffic flow at intersections and controlled road sections.

On any public road.

To inform drivers that overtaking vehicles is prohibited for the next 500m.

If this sign is displayed, do not overtake any vehicle for the next 500m.

Overview The Overtaking Prohibited Sign in South Africa is a regulatory prohibition sign used on public roads to restrict unsafe passing manoeuvres. It warns drivers that overtaking other vehicles is not allowed for a specified distance ahead, typically indicated as 500 metres unless otherwise stated. What the Sign Means When a driver encounters this sign, it means they are not permitted to overtake any moving vehicle within the indicated stretch of road. This restriction is usually in place due to road conditions, visibility issues, or safety risks such as curves, hills, or narrow lanes. The key rule is: no overtaking allowed for the next 500 metres (or as indicated). Driver Responsibilities Do not attempt to overtake any vehicle within the restricted zone Maintain a safe following distance behind other vehicles Stay in your lane and avoid unnecessary lane changes Be patient until the overtaking restriction ends Watch for additional warning or end-of-restriction signs Where You Will See This Sign This sign is commonly found: On steep inclines or declines Along winding or narrow rural roads In areas with limited visibility such as fog-prone zones Near intersections or high-risk accident zones Purpose of the Sign The purpose of the Overtaking Prohibited Sign is to improve road safety by preventing dangerous passing manoeuvres in areas where visibility or road conditions make overtaking unsafe. Common Mistakes to Avoid Attempting to overtake before the restriction ends Ignoring solid road markings associated with the sign Misjudging distance or visibility on curves or hills Following other vehicles too closely in frustration Safety Tips Always obey overtaking restriction signage immediately Maintain a safe and steady speed in restricted zones Look out for oncoming traffic on blind bends Wait for safe and legal overtaking zones before passing Penalties for Ignoring the Sign Ignoring an Overtaking Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of head-on collisions Legal liability in case of accidents Summary The Overtaking Prohibited Sign in South Africa prevents vehicles from overtaking for a specified distance, typically 500 metres. It is used to enhance safety in areas where road conditions make passing other vehicles dangerous.

On any public road.

To inform drivers that overtaking vehicles is prohibited for the next 500m.

If you are driving a heavy motor vehicle, do not overtake another heavy vehicle if sign R215 is displayed.

Overview The Overtaking by Goods Vehicle Prohibited Sign in South Africa is a regulatory prohibition sign used on public roads to control heavy vehicle movement. It specifically restricts goods vehicles from overtaking other vehicles for a designated distance, typically 500 metres unless otherwise indicated. What the Sign Means When a driver of a goods vehicle (such as a truck or freight carrier) encounters this sign, it means they are not allowed to overtake any other vehicle within the restricted section of road. This rule is usually applied for safety reasons, such as narrow roads, steep gradients, or areas with limited visibility. The key rule is: goods vehicles must not overtake for the next 500 metres (or as indicated). Driver Responsibilities Goods vehicle drivers must remain in their lane and avoid overtaking Maintain a safe and steady following distance Do not attempt to pass slower-moving vehicles in restricted zones Watch for the end of restriction signage before overtaking Adjust driving behaviour to road conditions and traffic flow Where You Will See This Sign This sign is commonly found: On steep hills and mountain passes Along narrow rural or winding roads In areas with high accident risk or limited visibility Near roadworks or temporary traffic control zones Purpose of the Sign The purpose of the Overtaking by Goods Vehicle Prohibited Sign is to improve road safety by preventing large and heavy vehicles from overtaking in areas where such manoeuvres could be dangerous or obstruct traffic flow. Common Mistakes to Avoid Attempting to overtake despite the restriction Ignoring distance-based overtaking limitations Misjudging road width or visibility on curves Following other vehicles too closely in frustration Safety Tips Obey all overtaking restrictions immediately upon seeing the sign Maintain safe spacing between vehicles Be patient in slow-moving traffic conditions Only overtake once it is clearly safe and legally permitted Penalties for Ignoring the Sign Ignoring an Overtaking by Goods Vehicle Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of serious collisions Legal liability in case of accidents involving heavy vehicles Summary The Overtaking by Goods Vehicle Prohibited Sign in South Africa restricts heavy vehicles from overtaking for a specified distance, typically 500 metres. It is designed to improve safety and traffic flow in areas where overtaking by large vehicles could be dangerous.

On a public road where the road is narrow, near an intersection or where a parked vehicle can impair the vision of other drivers.

To prohibit drivers from parking during any time of the day or night.

Do not park where these signs are displayed.

Overview The Parking Prohibited Sign in South Africa is a regulatory prohibition sign used on public roads to control where vehicles are allowed to stop and remain stationary. It is typically placed in areas where parked vehicles could obstruct traffic flow or reduce visibility for other road users. What the Sign Means When a driver sees this sign, it means that parking is not allowed at any time, day or night, in the designated area. This restriction applies even if the driver remains in the vehicle for a short period. The key rule is: no parking is permitted at any time. Driver Responsibilities Do not park your vehicle in the restricted zone Do not stop for extended periods unless explicitly allowed Keep intersections, bends, and narrow roads clear Follow nearby signage for alternative parking areas Avoid obstructing visibility for other road users Where You Will See This Sign This sign is commonly found: On narrow roads where space is limited Near intersections to improve visibility At bends or curves with restricted sight distance In busy urban streets and loading zones Purpose of the Sign The purpose of the Parking Prohibited Sign is to improve road safety and traffic flow by ensuring that stationary vehicles do not obstruct movement or reduce visibility for other drivers. Common Mistakes to Avoid Confusing “no parking” with “no stopping” rules Leaving a vehicle unattended in restricted zones Parking too close to intersections or bends Assuming short stops are allowed where they are not Safety Tips Always look for designated parking areas before stopping Check signage carefully when parking in urban areas Avoid stopping near intersections or narrow road sections Ensure your vehicle does not obstruct traffic or visibility Penalties for Ignoring the Sign Ignoring a Parking Prohibited Sign is a traffic offence and may result in: Fines Vehicle towing or clamping Demerit points (where applicable) Obstruction-related penalties Summary The Parking Prohibited Sign in South Africa prevents vehicles from being parked in unsafe or obstructive locations. It helps maintain visibility, safety, and smooth traffic flow on public roads.

On any public road. The sign may be supplemented by a red "no stopping line".

To ensure traffic flow and prevent that driver’s views are not impaired by stationary vehicles.

Do not stop unless to obey a traffic light or a traffic officer or to avoid a collision.

Overview The Stopping Prohibited Sign in South Africa is a regulatory prohibition sign used on public roads to control where vehicles may not stop at all. It is often accompanied by a red “no stopping” road marking line to reinforce the restriction. What the Sign Means When a driver sees this sign, it means stopping the vehicle is strictly prohibited at any time, even for a short duration. This includes stopping to pick up or drop off passengers or waiting in stationary traffic conditions that are not part of normal congestion. The key rule is: no stopping under any circumstances in the designated area. Driver Responsibilities Do not stop your vehicle in the restricted zone Do not pick up or drop off passengers in this area Keep traffic lanes, intersections, and sight lines clear Continue driving to a safe and permitted stopping area Observe both the sign and any accompanying road markings Where You Will See This Sign This sign is commonly found: Near intersections where visibility must remain clear On bridges, bends, and narrow road sections Along busy urban roads with high traffic flow Near pedestrian crossings or hazardous road sections Purpose of the Sign The purpose of the Stopping Prohibited Sign is to ensure uninterrupted traffic flow and maintain clear visibility for all road users. It helps prevent accidents caused by unexpected stationary vehicles in dangerous or high-traffic areas. Common Mistakes to Avoid Stopping briefly “just for a moment” in a no-stopping zone Confusing “no stopping” with “no parking” restrictions Picking up passengers in restricted areas Ignoring accompanying red road markings Safety Tips Always look for safe stopping zones before slowing down Plan passenger pick-up and drop-off points in advance Follow both signage and road markings carefully Keep intersections and narrow sections completely clear Penalties for Ignoring the Sign Ignoring a Stopping Prohibited Sign is a traffic offence and may result in: Fines Vehicle towing or removal Demerit points (where applicable) Increased liability if obstruction causes an accident Summary The Stopping Prohibited Sign in South Africa forbids all forms of stopping in designated areas. It is used to maintain traffic flow, improve visibility, and enhance road safety in high-risk or high-traffic zones.

At the beginning of and at entrances to any carriageway, lane or path.

To prohibit pedestrians from proceeding past this sign where they could cause a danger to themselves and to vehicles.

If you are a pedestrian, do not access this road where this sign is displayed.

Overview The Pedestrian Prohibited Sign in South Africa is a regulatory prohibition sign used to restrict pedestrian access to certain roads, lanes, or paths. It is placed where walking would be unsafe due to traffic conditions or where pedestrians could interfere with vehicle movement. What the Sign Means When a pedestrian encounters this sign, it means they are not allowed to proceed beyond that point on foot. The restriction is in place to protect both pedestrians and motorists from dangerous interactions. The key rule is: no pedestrian access beyond this point. Pedestrian Responsibilities Do not walk beyond the sign into restricted road areas Use designated sidewalks, crossings, or pedestrian routes Follow alternative walking paths provided nearby Avoid entering carriageways or high-speed traffic zones Remain alert to surrounding traffic conditions at all times Where You Will See This Sign This sign is commonly found: On highways and freeways At road tunnels and bridges without pedestrian access In industrial or restricted vehicle-only areas At entrances to high-speed or dangerous road sections Purpose of the Sign The purpose of the Pedestrian Prohibited Sign is to protect pedestrians from entering dangerous traffic environments and to prevent disruptions to vehicle flow on roads not designed for foot traffic. Common Mistakes to Avoid Walking along highways or high-speed roads Ignoring pedestrian-only route alternatives Entering restricted carriageways for shortcuts Misunderstanding access rules in industrial areas Safety Tips Always use designated pedestrian sidewalks and crossings Pay attention to warning and prohibition signage Avoid walking near fast-moving traffic Plan safe walking routes in unfamiliar areas Penalties for Ignoring the Sign Ignoring a Pedestrian Prohibited Sign is a violation and may result in: Fines (where applicable under local bylaws) Removal from restricted road areas by authorities Increased risk of serious injury or fatal accidents Summary The Pedestrian Prohibited Sign in South Africa prevents pedestrians from entering unsafe or vehicle-only road areas. It is designed to protect lives and maintain safe separation between pedestrians and vehicular traffic.

At the beginning of or entrance to any carriageway, lane or path.

To prohibit cyclists from using the carriageway, lane or path where they can cause a danger to themselves and to other road users.

If you are a pedal cyclist, do not access this road where this sign is displayed.

Overview The Pedal Cycle Prohibited Sign in South Africa is a regulatory prohibition sign used to restrict cyclists from entering certain roads, lanes, or paths. It is typically placed in areas where cycling would be unsafe or could interfere with other traffic. What the Sign Means When a cyclist encounters this sign, it means they are not allowed to proceed beyond that point on a bicycle. The restriction is intended to prevent dangerous situations involving cyclists and other road users. The key rule is: no cycling beyond this point. Cyclist Responsibilities Do not ride beyond the sign into restricted areas Use designated cycling lanes or alternative routes Dismount and walk the bicycle if necessary (only where permitted) Follow all traffic rules applicable to cyclists Remain aware of surrounding traffic conditions Where You Will See This Sign This sign is commonly found: On highways and high-speed roads At entrances to pedestrian-only areas On narrow roads or paths not suitable for bicycles In tunnels, bridges, or restricted traffic zones Purpose of the Sign The purpose of the Pedal Cycle Prohibited Sign is to protect cyclists from hazardous conditions and to ensure the safe and efficient movement of traffic. It helps prevent conflicts between bicycles and motor vehicles or pedestrians. Common Mistakes to Avoid Ignoring the sign and continuing to ride in restricted areas Assuming short distances are exempt from the rule Using high-speed roads not designed for cyclists Failing to look for alternative cycling routes Safety Tips Always obey cycling restriction signs Plan routes that include safe cycling infrastructure Use protective gear and remain visible Be cautious when transitioning between permitted and restricted areas Penalties for Ignoring the Sign Ignoring a Pedal Cycle Prohibited Sign may result in: Fines (where applicable) Removal from restricted areas by authorities Increased risk of accidents or injury Summary The Pedal Cycle Prohibited Sign in South Africa restricts cyclists from entering certain roads or paths where it may be unsafe. It helps protect cyclists and other road users by ensuring proper use of designated transport routes.

At the beginning of or entrance to a carriageway, lane or path.

To prevent cyclists and pedestrians from using a certain road or a certain section of a road where they can cause a danger to themselves or other road users.

Pedal cyclists and pedestrians are not allowed to access or make use of the road where this sign is displayed.

Overview The Pedal Cycle & Pedestrian Prohibited Sign in South Africa is a regulatory prohibition sign used to restrict both cyclists and pedestrians from entering certain roads, lanes, or paths. It is typically placed in areas where their presence could create dangerous situations due to traffic speed, road design, or limited space. What the Sign Means When road users encounter this sign, it means that both pedestrians and cyclists are not allowed to proceed beyond that point. The restriction ensures that only authorised vehicle traffic uses the designated road or section. The key rule is: no pedestrians or cyclists beyond this point. Pedestrian & Cyclist Responsibilities Do not walk or cycle past the sign into restricted areas Use designated sidewalks, crossings, or cycling routes Follow alternative safe paths where provided Avoid entering high-speed or vehicle-only zones Remain aware of traffic and surrounding hazards Where You Will See This Sign This sign is commonly found: On highways and freeways At entrances to tunnels or bridges without pedestrian access In industrial or restricted traffic areas On roads with high-speed or heavy vehicle traffic Purpose of the Sign The purpose of the Pedal Cycle & Pedestrian Prohibited Sign is to enhance safety by preventing vulnerable road users from entering hazardous environments. It also helps maintain smooth and uninterrupted traffic flow for vehicles. Common Mistakes to Avoid Ignoring the restriction and entering unsafe road sections Using restricted roads as shortcuts Failing to look for alternative pedestrian or cycling routes Underestimating the danger of high-speed traffic areas Safety Tips Always obey prohibition signs for your safety Plan routes using designated pedestrian and cycling infrastructure Stay away from high-speed or vehicle-only roads Be especially cautious in unfamiliar environments Penalties for Ignoring the Sign Ignoring a Pedal Cycle & Pedestrian Prohibited Sign may result in: Fines (where applicable) Removal from restricted areas by authorities Increased risk of serious injury or accidents Summary The Pedal Cycle & Pedestrian Prohibited Sign in South Africa restricts both cyclists and pedestrians from entering certain roads or areas. It is designed to protect vulnerable road users and ensure safe, efficient movement of vehicular traffic.

On any public road and at the beginning of pedestrian and separate cycle lanes.

To prohibit motorcycles, on part of a carriageway, for safety reasons.

Motorcyclists may not enter this part of the carriageway, or if this sign is displayed on a freeway, motorcyclists must leave at the first exit.

Overview The Motor Cycle Prohibited Sign in South Africa is a regulatory prohibition sign used on public roads to restrict the use of motorcycles in certain areas. It is commonly placed where motorcycles could pose a safety risk to other road users or where road design is unsuitable for them. What the Sign Means When a rider encounters this sign, it means motorcycles are not allowed to enter or use the specified road, lane, or path. The restriction is in place to protect both motorcyclists and other road users. The key rule is: no motorcycles allowed beyond this point. Motorcyclist Responsibilities Do not enter restricted roads or lanes on a motorcycle Use alternative approved routes for motorcyclists Follow signage indicating shared or permitted lanes Be attentive to separate cycle or pedestrian zones Comply with all road safety restrictions Where You Will See This Sign This sign is commonly found: At the start of pedestrian-only or cycle-only lanes On narrow or restricted urban pathways In pedestrian precincts or malls In areas where motorcycles could create safety hazards Purpose of the Sign The purpose of the Motor Cycle Prohibited Sign is to improve safety by preventing motorcycles from entering areas where their presence could endanger pedestrians, cyclists, or other motorists. Common Mistakes to Avoid Entering pedestrian or cycle lanes on a motorcycle Ignoring signage in restricted urban areas Assuming short distances are exempt from the restriction Using prohibited areas as shortcuts Safety Tips Always check signage before entering shared or restricted lanes Use designated motorcycle-friendly routes Slow down in mixed-use urban environments Be especially cautious near pedestrians and cyclists Penalties for Ignoring the Sign Ignoring a Motor Cycle Prohibited Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Removal from restricted areas by authorities Increased risk of accidents or injury Summary The Motor Cycle Prohibited Sign in South Africa restricts motorcycles from entering specific roads or lanes for safety reasons. It helps protect vulnerable road users and ensures safe separation of different types of traffic.

On any public road, lane, path or area.

To prohibit motorcars from entering the area, for safety or any other reasons.

Do not enter this area if you are driving a motorcar.

Overview The Motor Car Prohibited Sign in South Africa is a regulatory prohibition sign used to restrict passenger vehicles (motorcars) from entering certain roads, lanes, paths, or areas. It is applied where motor vehicle access is unsafe, unnecessary, or reserved for other types of road users. What the Sign Means When a driver encounters this sign, it means that standard passenger vehicles are not allowed to enter or use the designated area. Only specifically permitted vehicles (such as emergency, maintenance, or authorised service vehicles, if indicated) may be allowed. The key rule is: no motorcars allowed beyond this point. Driver Responsibilities Do not enter restricted areas with a passenger vehicle Look for alternative routes or designated access roads Follow any additional access control signage Respect pedestrian-only or specialised-use zones Be alert for enforcement or physical barriers Where You Will See This Sign This sign is commonly found: In pedestrian zones and city centres On private or controlled-access roads In parks, nature reserves, or tourist walkways Near maintenance, industrial, or service-only areas Purpose of the Sign The purpose of the Motor Car Prohibited Sign is to enhance safety and manage access by preventing passenger vehicles from entering areas where they may cause danger, congestion, or environmental disruption. Common Mistakes to Avoid Entering pedestrian or restricted zones by mistake Assuming short access routes are permitted Ignoring barriers or supplementary warning signs Using prohibited areas as shortcuts Safety Tips Always check access restrictions before entering unfamiliar areas Use designated parking and drop-off points Follow signage indicating permitted vehicle types Drive slowly near shared pedestrian environments Penalties for Ignoring the Sign Ignoring a Motor Car Prohibited Sign is a traffic offence and may result in: Fines Vehicle removal or towing Demerit points (where applicable) Restricted access enforcement by authorities Summary The Motor Car Prohibited Sign in South Africa restricts passenger vehicles from entering certain areas for safety, environmental, or access-control reasons. It ensures that only appropriate users are allowed in sensitive or restricted zones.

On any public road, lane, path or area.

Indicates to the driver of a taxi that he or she shall not proceed beyond such sign.

Do not enter this area if you are driving a taxi.

Overview The Taxi Prohibited Sign in South Africa is a regulatory prohibition sign used to restrict taxis from entering or using certain roads, lanes, paths, or areas. It is typically installed in locations where taxi access may interfere with traffic management, pedestrian safety, or controlled transport systems. What the Sign Means When a taxi driver encounters this sign, it means that taxis are not permitted to proceed beyond that point. The restriction applies specifically to vehicles operating as taxis, whether formal or informal. The key rule is: taxis are not allowed beyond this sign. Taxi Driver Responsibilities Do not enter restricted zones marked for no-taxi access Use designated taxi ranks or approved pick-up points Follow alternative routes provided by signage or authorities Comply with local transport regulations and permits Avoid stopping or picking up passengers in prohibited areas Where You Will See This Sign This sign is commonly found: In city centres with regulated traffic zones Near bus-only or public transport priority lanes At pedestrian precincts and restricted urban areas In controlled access roads or special event zones Purpose of the Sign The purpose of the Taxi Prohibited Sign is to regulate taxi movement in sensitive or high-traffic areas. It helps reduce congestion, improve safety, and ensure proper use of designated public transport facilities. Common Mistakes to Avoid Entering restricted taxi-free zones without authorisation Using prohibited areas as shortcuts for passenger pick-up Ignoring alternative designated taxi routes Stopping in areas reserved for other transport modes Safety Tips Always observe taxi-specific restriction signage carefully Use official taxi ranks or designated stops Plan routes that comply with transport regulations Be aware of shared and restricted transport zones in cities Penalties for Ignoring the Sign Ignoring a Taxi Prohibited Sign is a traffic offence and may result in: Fines Vehicle impoundment or enforcement action Demerit points (where applicable) Loss of operating permissions in some cases Summary The Taxi Prohibited Sign in South Africa restricts taxis from entering specific roads or areas. It is used to improve traffic management, reduce congestion, and ensure safe and organised transport systems.

On any public road, lane, path or area.

Indicates to the driver of a minibus that he or she shall not proceed beyond such sign.

Do not enter this area if you are driving a minibus.

Overview The Minibus Prohibited Sign in South Africa is a regulatory prohibition sign used to restrict minibuses from entering certain roads, lanes, paths, or areas. It is typically applied in locations where minibus operations could interfere with traffic flow, safety, or regulated transport systems. What the Sign Means When a minibus driver encounters this sign, it means that minibuses are not allowed to proceed beyond the point where the sign is placed. The restriction applies regardless of passenger load or service type. The key rule is: no minibuses allowed beyond this point. Driver Responsibilities Do not enter restricted areas with a minibus Follow designated routes for minibus transport Use official taxi ranks or transport facilities Comply with all access control and traffic signage Avoid picking up or dropping off passengers in prohibited zones Where You Will See This Sign This sign is commonly found: In central business districts with regulated traffic flow Near pedestrian-only or restricted urban areas On roads reserved for buses or other public transport modes At entrances to controlled-access or special-use zones Purpose of the Sign The purpose of the Minibus Prohibited Sign is to improve road safety and traffic management by preventing minibuses from entering areas where their presence may cause congestion, conflict with other transport modes, or endanger pedestrians. Common Mistakes to Avoid Entering restricted zones to shorten travel routes Ignoring signage in busy urban transport areas Stopping in prohibited zones for passenger pickup or drop-off Confusing permitted bus routes with minibus access routes Safety Tips Always check transport-specific signage before entering city areas Use designated minibus routes and stops Follow local transport authority instructions Be aware of shared public transport zones Penalties for Ignoring the Sign Ignoring a Minibus Prohibited Sign is a traffic offence and may result in: Fines Vehicle impoundment or enforcement action Demerit points (where applicable) Possible suspension of operating privileges in regulated areas Summary The Minibus Prohibited Sign in South Africa restricts minibuses from entering certain roads or areas. It is used to regulate transport systems, improve traffic flow, and ensure safety in controlled or high-density urban environments.