On the left-hand side of any road

To indicate that there is an exit about 300m, 200m and 100m ahead.

This sign indicates an off-ramp in 100 meters. If possible enter the exit at the same speed as the maximum speed for that road.

Overview The Information Signs (South Africa) – Countdown Sign are placed on the left-hand side of roads, especially highways and freeways, to inform drivers of an upcoming exit (off-ramp) and the distance remaining before it. What the Sign Means Countdown signs typically appear in stages (for example 300 m, 200 m, and 100 m) to guide drivers as they approach an exit. The final sign indicates that the off-ramp is approximately 100 metres ahead. The key purpose is: to warn drivers of an approaching exit and help them prepare to safely leave the main road at the correct point. How It Works in Practice Multiple signs appear at decreasing distances before the exit. Drivers are given time to move into the correct lane. The final countdown sign indicates the exit is very close (about 100 m). Safe merging into the off-ramp is required at the appropriate speed. Driver Responsibilities Start preparing for the exit as soon as countdown signs appear Move into the correct lane early if necessary Reduce speed smoothly before entering the off-ramp if required Do not make sudden lane changes near the exit Where You Will See This Sign On highways and freeways before major exits At urban freeway interchanges Near toll roads or major junctions Where high-speed roads require advance exit preparation Purpose of the Sign Countdown signs help drivers safely prepare for exits by giving clear distance information, reducing sudden lane changes and improving traffic flow near off-ramps. Common Mistakes to Avoid Missing early countdown signs and reacting too late Crossing multiple lanes suddenly near the exit Braking sharply on the main carriageway Exiting at unsafe speeds or angles Safety Tips Plan your exit in advance Signal early before changing lanes Maintain steady speed until safely in the off-ramp lane Adjust speed only once you are in the exit lane Penalties for Ignoring the Sign Ignoring countdown signage may result in: Dangerous last-minute lane changes Collisions with other vehicles Missed exits leading to unsafe driving maneuvers Traffic violations for reckless driving Summary Countdown signs in South Africa warn drivers of an approaching exit and help them prepare in advance. Drivers should plan early, move into the correct lane safely, and adjust speed smoothly when exiting the freeway.

On the left-hand side of any road

To indicate that there is an exit about 300m, 200m and 100m ahead.

This sign indicates an off-ramp in 200 meters. If possible enter the exit at the same speed as the maximum speed for that road.

Overview The Information Signs (South Africa) – Countdown Sign is used on highways and major roads to inform drivers how far they are from an upcoming exit or off-ramp. It is usually placed on the left-hand side of the road. What the Sign Means This sign indicates the distance remaining before an exit, typically shown in stages such as 300m, 200m, and 100m. A countdown sign helps drivers prepare in advance to safely change lanes and exit the roadway. How It Works in Practice Gives advance warning of an upcoming off-ramp. Helps drivers plan lane changes safely. Reduces sudden braking or last-minute decisions. Indicates progressively closer distances to the exit. Driver Responsibilities Start preparing to exit as soon as you see the first countdown sign Move into the correct lane early Maintain a safe and steady speed Avoid sudden lane changes near the exit Where You Will See This Sign This sign is commonly found: On highways and freeways Approaching major interchanges Near urban off-ramps and exit routes On multi-lane roads with controlled access exits Purpose of the Sign The purpose of the countdown sign is to guide drivers in preparing for an upcoming exit, improving traffic flow and reducing last-second lane changes that could cause accidents. Common Mistakes to Avoid Waiting too long before changing lanes Braking suddenly at the exit point Missing the exit due to poor lane planning Crossing multiple lanes at the last moment Safety Tips Plan your exit early when you see the first countdown marker Match your speed with surrounding traffic Use indicators in good time before changing lanes Stay calm and avoid rushed movements Penalties for Ignoring the Sign Ignoring countdown signs may result in: Missed exits and unsafe reversing or weaving Collisions from sudden lane changes Traffic disruption on high-speed roads Fines for unsafe driving behaviour Summary The countdown sign in South Africa provides advance warning of an upcoming exit. Drivers must prepare early, change lanes safely, and maintain appropriate speed to exit smoothly and safely.

On the left-hand side of any road

To indicate that there is an exit about 300m, 200m and 100m ahead.

This sign indicates an off-ramp in 300 meters. If possible enter the exit at the same speed as the maximum speed for that road.

Overview The Information Signs (South Africa) – Countdown Sign are placed on the left-hand side of highways and major roads to inform drivers that an exit (off-ramp) is approaching and to show the remaining distance to it. What the Sign Means Countdown signs are displayed in sequence (typically 300 m, 200 m, and 100 m) to help drivers prepare in advance for leaving the main road. This specific sign indicates that the off-ramp is approximately 300 metres ahead, giving drivers early notice to prepare for the exit. The key purpose is: to warn drivers of an upcoming exit and give advance distance information to allow safe lane positioning and smooth exiting. How It Works in Practice The first countdown sign appears about 300 m before the exit. Additional signs follow at 200 m and 100 m. Drivers use the distance markers to prepare for lane changes. The exit becomes progressively closer with each sign. Driver Responsibilities Start planning your exit when you see the 300 m sign Move into the correct lane early and safely Maintain steady speed on the main carriageway Only adjust speed once in the exit lane if needed Where You Will See This Sign On freeways and highways before off-ramps At major urban interchanges Near toll roads and high-speed exits Where advance warning is needed for safe exiting Purpose of the Sign Countdown signs are designed to improve road safety by giving drivers early and clear distance information so they can position themselves correctly and exit safely without sudden lane changes or braking. Common Mistakes to Avoid Ignoring the early 300 m warning Changing lanes too late near the exit Sudden braking on fast-moving traffic lanes Crossing multiple lanes in a short distance Safety Tips Plan your exit as soon as you see the first countdown sign Signal early when changing lanes Keep a steady speed while positioning yourself Only reduce speed once safely in the exit lane Penalties for Ignoring the Sign Ignoring countdown signs may lead to: Unsafe last-minute lane changes Collisions with nearby vehicles Missing exits and making dangerous corrections Traffic violations for reckless driving behaviour Summary The 300 m countdown sign in South Africa warns drivers of an upcoming exit and gives early distance guidance. Drivers should prepare in advance, change lanes safely, and exit smoothly without sudden movements.

Displayed on the left-hand side of any road.

To inform you that the road ahead or the road to the left or right ends.

Do not turn in at such a road unless you are going to a destination in the road that ends.

Overview The Information Signs (South Africa) – Cul-de-Sac Sign is used on public roads to inform drivers that a road ahead, or a side road to the left or right, ends in a dead end with no through access. What the Sign Means This sign indicates that the road does not continue beyond a certain point and will terminate in a closed end or turning area. Drivers should only enter if they intend to access a destination within that road. How It Works in Practice The road leads to a dead end with no exit through traffic. Vehicles must turn around within the cul-de-sac. There is no connection to other roads beyond the endpoint. Traffic is usually local or residential only. Driver Responsibilities Check whether your destination is within the cul-de-sac Avoid entering if you are just passing through Drive slowly when entering residential dead-end roads Be prepared to turn around safely at the end Where You Will See This Sign This sign is commonly found: In residential suburbs and housing estates On short access roads or service roads In industrial or private property areas At the entrance to dead-end streets Purpose of the Sign The purpose of the cul-de-sac sign is to inform drivers that a road does not continue through, helping them avoid unnecessary entry and improving traffic flow and navigation efficiency. Common Mistakes to Avoid Entering expecting a through route Driving too fast into residential dead ends Ignoring that turning around will be required Confusing cul-de-sacs with through streets Safety Tips Slow down when entering unfamiliar side roads Confirm your destination is within the road before entering Watch for pedestrians and parked vehicles Turn around carefully at the end of the road Penalties for Ignoring the Sign Ignoring cul-de-sac information may result in: Unnecessary detours and delays Unsafe reversing or turning at the dead end Traffic congestion in narrow residential roads Minor property or vehicle damage Summary The cul-de-sac sign in South Africa informs drivers that a road ends ahead with no through route. Drivers should only enter if necessary and be prepared to turn around safely at the end.

Displayed on the left-hand side of any road.

To inform you that the road ahead or the road to the left or right ends.

Do not turn in at such a road unless you are going to a destination in the road that ends.

Overview The Information Signs (South Africa) – Cul-de-Sac Sign is used on roads to inform drivers that a road ahead, or a side road to the left or right, ends in a dead end with no through traffic. What the Sign Means This sign indicates that the road does not continue beyond the endpoint. It serves as a navigation warning that entry should only be made if the driver’s destination is within that road. How It Works in Practice The road terminates at a dead end. There is no connection to other through roads. Vehicles must turn around at the end of the street. Traffic is typically local or residential only. Driver Responsibilities Confirm your destination is within the cul-de-sac before entering Avoid entering if you are just passing through Drive slowly in residential or narrow dead-end roads Be prepared to turn around safely at the end Where You Will See This Sign This sign is commonly found: In residential suburbs and housing developments On short access or service roads In industrial estates or private property areas At entrances to dead-end streets Purpose of the Sign The purpose of the cul-de-sac sign is to warn drivers that a road ends ahead, helping them avoid unnecessary entry and ensuring smoother traffic flow and safer navigation. Common Mistakes to Avoid Entering expecting a through route Driving too fast into dead-end streets Ignoring the need to turn around at the end Confusing cul-de-sacs with connecting roads Safety Tips Slow down when entering unfamiliar roads Check whether your destination is located within the road Watch for pedestrians and parked vehicles Turn around carefully and safely at the end Penalties for Ignoring the Sign Ignoring this information may result in: Unnecessary detours or delays Unsafe reversing or turning maneuvers Minor traffic congestion in narrow streets Potential minor property or vehicle damage Summary The cul-de-sac sign in South Africa warns drivers that a road does not continue beyond a certain point. Drivers should only enter if necessary and be prepared to turn around safely at the end of the road.

Displayed on the left-hand side of any road.

To inform you that the road ahead or the road to the left or right ends.

Do not turn in at such a road unless you are going to a destination in the road that ends.

Overview The Information Signs (South Africa) – Cul-de-Sac Sign is used on public roads to indicate that a road ahead, or a side road to the left or right, does not continue and ends in a dead end. What the Sign Means This sign informs drivers that there is no through route beyond the indicated road. The road terminates, and vehicles entering it will need to turn around to exit. How It Works in Practice The road ends in a dead-end or turning area. No continuation to other roads is available. Only local access traffic usually uses the road. Drivers must reverse or turn around to leave. Driver Responsibilities Only enter if your destination is within the cul-de-sac Do not enter expecting a through route Drive slowly in narrow or residential dead-end roads Be prepared to turn safely at the end Where You Will See This Sign This sign is commonly found: In residential suburbs and housing estates On short access roads or service roads In industrial or private developments At entrances to dead-end streets Purpose of the Sign The purpose of the cul-de-sac sign is to inform drivers that a road has no exit, helping them avoid unnecessary entry and improving traffic flow and safety in residential or restricted areas. Common Mistakes to Avoid Entering while expecting a connecting road Driving too fast into dead-end streets Failing to plan for turning around at the end Confusing cul-de-sacs with through roads Safety Tips Slow down when entering unfamiliar side roads Check if your destination is located within the street Watch for pedestrians and parked vehicles Turn around carefully at the end of the road Penalties for Ignoring the Sign Ignoring this warning may result in: Unnecessary detours and delays Unsafe reversing or turning manoeuvres Minor congestion in narrow residential streets Possible minor property or vehicle damage Summary The cul-de-sac sign in South Africa warns drivers that a road ends ahead with no through access. Drivers should only enter if necessary and be prepared to turn around safely at the end.

On any road.

To inform you that you have the right of way at the intersection ahead.

Do not slow down unnecessarily, but make sure that other traffic will yield.

Overview The Information Signs (South Africa) – Right of Way Sign are used on public roads to inform drivers that they have priority at an upcoming intersection. This means other traffic is required to yield to them. What the Sign Means This sign indicates that your vehicle has the right of way at the intersection ahead, and cross-traffic or joining traffic must give way. The key purpose is: to inform drivers that they have priority at the intersection and may proceed, provided it is safe to do so. How It Works in Practice The road you are travelling on has priority at the intersection. Other roads must yield or stop for your traffic flow. Traffic control markings or signs support this priority. Right of way does not remove the need for caution. Driver Responsibilities Proceed without unnecessary slowing if the way is clear Remain alert for vehicles that may fail to yield Be prepared to slow down or stop if needed Check all directions before entering the intersection Where You Will See This Sign At priority intersections on main roads On arterial routes crossing smaller roads In urban and suburban road networks Where traffic flow is regulated to favour a main route Purpose of the Sign The right of way sign is used to improve traffic flow by clearly indicating which road has priority at an intersection, reducing confusion and helping vehicles move smoothly through junctions. Common Mistakes to Avoid Assuming all vehicles will automatically yield Driving too fast into intersections without checking Ignoring cross traffic that fails to obey rules Failing to remain alert at junctions Safety Tips Maintain a safe and controlled speed Scan the intersection before proceeding Be ready to react to unpredictable drivers Do not assume right of way guarantees safety Penalties for Ignoring Rules Even with right of way, unsafe driving may result in: Collisions if other drivers fail to yield or you proceed recklessly Fines for negligent or dangerous driving Liability in intersection accidents Traffic violations if control rules are ignored Summary The right of way sign in South Africa informs drivers that they have priority at an intersection. However, drivers must still remain cautious and ensure the intersection is clear before proceeding.

At the entrance to a parking area.

To inform you of the existence of a park-and-ride terminus that has a bus or train service.

Stop in this parking area if you want to reach your destination using other transport.

Overview The Information Signs (South Africa) – Park and Ride Sign is used at the entrance to designated parking areas that connect with public transport services such as buses or trains. What the Sign Means This sign informs drivers that there is a park-and-ride facility ahead where they can park their vehicle and continue their journey using public transport. It is designed to reduce traffic congestion and encourage shared transport use. How It Works in Practice Drivers park their private vehicles in a secure facility. They transfer to buses, trains, or shuttle services. The system helps reduce traffic into busy urban areas. It is often linked to major transport routes or city centres. Driver Responsibilities Enter the parking area if you intend to use public transport Follow parking rules and signage within the facility Ensure your vehicle is securely parked before leaving Be aware of public transport schedules and routes Where You Will See This Sign This sign is commonly found: At entrances to park-and-ride facilities Near train stations and bus terminals On the outskirts of major cities Along highways leading into urban centres Purpose of the Sign The purpose of the park-and-ride sign is to guide drivers to designated parking areas where they can switch to public transport, helping to reduce traffic congestion and improve commuting efficiency. Common Mistakes to Avoid Entering without understanding the transport connection Parking outside designated areas Leaving valuables visible in parked vehicles Confusing park-and-ride areas with general parking lots Safety Tips Follow all signage within the facility Lock your vehicle before leaving it Use only official transport services linked to the site Be aware of pedestrian movement around transport hubs Penalties for Ignoring the Sign Ignoring park-and-ride instructions may result in: Parking violations or fines Towing of improperly parked vehicles Restricted access to transport services Traffic congestion in surrounding areas Summary The park-and-ride sign in South Africa informs drivers of a facility where they can park and transfer to public transport. It helps reduce congestion and supports efficient urban travel.

Below another sign.

To indicate a recommended speed on this road.

As far as possible, attempt to travel at the recommended speed.

Overview The Information Signs (South Africa) – Supplementary Plate Sign are displayed below another road sign to provide additional information, most commonly a recommended speed for a specific section of road. What the Sign Means This sign does not impose a legal speed limit. Instead, it gives a recommended or advised speed that is considered safe for the road conditions ahead, such as curves, slopes, or hazards. The key purpose is: to inform drivers of a recommended safe speed and encourage them to adjust their driving accordingly. How It Works in Practice The plate is placed directly under another warning or regulatory sign. It indicates a suggested speed based on road conditions. It is especially useful on curves, descents, or complex intersections. The recommendation is based on safety, not enforcement. Driver Responsibilities Adjust speed to match road conditions where possible Use extra caution if conditions are wet, dark, or unfamiliar Do not treat the recommendation as a fixed legal limit Maintain full control of the vehicle at all times Where You Will See This Sign At sharp curves or winding roads On steep descents or ascents Near hazardous or complex intersections In temporary roadwork or changed road conditions Purpose of the Sign Supplementary plate signs help improve road safety by giving drivers clear guidance on appropriate speeds for specific conditions, reducing the risk of accidents in challenging areas. Common Mistakes to Avoid Ignoring recommended speeds entirely Treating the advisory speed as a legal requirement Maintaining high speed in hazardous conditions Failing to adjust for weather or visibility Safety Tips Slow down in advance of the sign Match your speed to road and weather conditions Use engine braking on descents where necessary Stay alert for additional warning signs Penalties for Ignoring the Sign While not legally enforceable as a speed limit, ignoring recommended speeds may result in: Loss of vehicle control Increased risk of collisions Liability in accident investigations Possible fines if driving is deemed negligent or reckless Summary The supplementary plate sign in South Africa provides recommended speed guidance beneath other signs. Drivers should adjust their speed where possible to match road conditions and maintain safe vehicle control.

Below another sign.

To indicate that the restriction applies for the next 12km.

Comply with the rules for the next 12km.

Overview The Information Signs (South Africa) – Supplementary Plate Sign is used beneath a main traffic sign to provide additional information about how long a restriction or instruction applies. What the Sign Means This sign indicates that the rule, warning, or restriction shown on the main sign continues for a specified distance — in this case, 12 kilometres. Drivers must comply with the instruction for the entire stated distance. How It Works in Practice It is not a standalone sign but supports another traffic sign. It defines the distance over which a rule applies. The restriction remains active until the distance ends. It helps drivers understand how long to follow a specific instruction. Driver Responsibilities Observe the main sign and its instruction carefully Apply the rule continuously for the full 12 km Do not assume the restriction ends early Stay alert for updated or ending signage Where You Will See This Sign This sign is commonly found: On highways and long rural roads In areas with extended speed or hazard zones Near roadworks or maintenance stretches Along routes with environmental or safety restrictions Purpose of the Sign The purpose of the supplementary plate sign is to clearly communicate the distance over which a traffic rule applies, helping drivers maintain compliance and avoid confusion on long road sections. Common Mistakes to Avoid Assuming the restriction ends sooner than indicated Ignoring the main sign while focusing only on distance Speeding up before the restriction ends Failing to watch for updated signage Safety Tips Remember that both the main sign and plate must be read together Maintain consistent driving behaviour for the full distance Stay alert for changing road conditions Adjust speed gradually rather than abruptly Penalties for Ignoring the Sign Ignoring a supplementary plate instruction may result in: Speeding or traffic violations Increased risk of accidents in controlled zones Fines for non-compliance with road regulations Endangering other road users in restricted areas Summary The supplementary plate sign in South Africa provides important distance-based instructions for traffic rules. Drivers must follow the associated main sign’s instruction for the full indicated distance of 12 km.

Below another sign.

To indicate that the restriction applies for the next 200m.

Comply with the rules for the next 200m.

Overview The Information Signs (South Africa) – Supplementary Plate Sign are placed below another road sign to provide extra details about how far a restriction or instruction applies. What the Sign Means This specific supplementary plate indicates that the restriction shown on the main sign applies for the next 200 metres of road. After that distance, the restriction may end or change. The key purpose is: to inform drivers that a specific road rule or restriction must be followed for a distance of 200 metres. How It Works in Practice The main sign shows a rule or restriction (e.g. speed, no overtaking, hazard warning). The supplementary plate indicates how far that rule applies. In this case, the condition applies for the next 200 m. After 200 m, normal driving conditions may resume or change. Driver Responsibilities Follow the main sign’s instruction immediately Maintain compliance for the full 200 m distance Stay alert for follow-up signs indicating changes Adjust speed or behaviour as required throughout the zone Where You Will See This Sign Roadwork or temporary construction zones Hazardous road sections (curves, narrow roads, etc.) Speed control or enforcement areas Areas with short-term traffic restrictions Purpose of the Sign Supplementary distance plates help drivers understand exactly how long a road restriction applies, reducing confusion and improving compliance with temporary or situational traffic rules. Common Mistakes to Avoid Ignoring the distance limitation Returning to normal driving too early Failing to notice follow-up warning signs Maintaining unsafe speed within the restricted zone Safety Tips Observe the main sign and apply its rule immediately Maintain safe driving for the full 200 m distance Watch for additional signage beyond the restriction zone Drive cautiously even when the restriction ends Penalties for Ignoring the Sign Ignoring distance-based restrictions may result in: Traffic fines for non-compliance Increased risk of accidents in controlled zones Liability in roadwork or hazard incidents Possible prosecution for reckless driving Summary The supplementary plate sign in South Africa indicates that a restriction applies for the next 200 metres. Drivers must follow the main sign’s instruction carefully for the full distance before returning to normal driving conditions.

Below another sign.

To give more information about the main message on regulatory, warning or diagrammatical guidance signs.

Pay attention to these signs in order to realise what the danger is, what a safe speed is, how far away the danger is and the distance the danger will continue.

Overview The Information Signs (South Africa) – Supplementary Plate Sign is a secondary sign placed below a main regulatory, warning, or guidance sign to provide extra details that help drivers understand the situation more clearly. What the Sign Means This sign adds important supporting information to the main sign above it. It helps explain the nature of a hazard, the distance to it, the duration of a restriction, or the appropriate driving response. How It Works in Practice It is always used together with a main road sign. It provides clarification such as distance, time, or extent of a hazard. It may indicate how far a danger extends or how long a rule applies. It helps drivers make better and safer decisions. Driver Responsibilities Read both the main sign and the supplementary plate together Adjust speed and driving behaviour based on the combined message Pay attention to distances or duration indicated Stay alert for continued or changing conditions Where You Will See This Sign This sign is commonly found: Below warning signs (e.g., curves, hazards, roadworks) Under regulatory signs (e.g., speed limits or restrictions) With directional or guidance signs In construction or temporary traffic control zones Purpose of the Sign The purpose of the supplementary plate sign is to provide additional clarity to a main traffic sign, helping drivers understand exactly what the hazard or rule involves, how far it applies, and how they should respond. Common Mistakes to Avoid Ignoring the supplementary plate and only reading the main sign Misjudging the distance or duration of a restriction Failing to adjust speed based on added information Assuming the main sign alone provides all necessary detail Safety Tips Always read both signs together as one instruction Adjust speed early based on full information Pay attention to distance and hazard extent Stay alert for additional or updated signage ahead Penalties for Ignoring the Sign Ignoring supplementary information may result in: Speeding or regulatory violations Accidents due to misunderstanding road conditions Fines for non-compliance with traffic instructions Increased risk in hazardous driving areas Summary The supplementary plate sign in South Africa provides essential extra information to a main traffic sign. Drivers must read both together to understand hazards, distances, and restrictions, and adjust their driving accordingly.

Below another sign.

To give more information about the main message on regulatory, warning or diagrammatical guidance signs.

Pay attention to these signs in order to realise what the danger is, what a safe speed is, how far away the danger is and the distance the danger will continue.

Overview The Information Signs (South Africa) – Supplementary Plate Sign are placed directly below a main road sign to provide extra details that help drivers better understand the instruction, warning, or guidance being given. What the Sign Means This type of sign does not stand alone. Instead, it supports a regulatory, warning, or directional sign by giving clearer information such as distance, duration, or specific conditions of a hazard or rule. The key purpose is: to provide additional information that helps drivers understand the nature, distance, speed, or duration of a road condition or instruction. How It Works in Practice It is always placed below another primary road sign. It clarifies what the main sign is warning or instructing about. It may indicate distance to a hazard or how long a rule applies. It can help define safe speeds or road conditions more clearly. Driver Responsibilities Read both the main sign and the supplementary plate together Adjust speed or behaviour according to full information provided Pay attention to distance or duration of hazards Remain alert for changing road conditions ahead Where You Will See This Sign Below warning signs (e.g. curves, hazards, slippery roads) Below regulatory signs (e.g. speed limits, restrictions) At roadworks or temporary traffic control zones On highways, rural roads, and urban intersections Purpose of the Sign Supplementary plates are used to improve road safety by giving drivers precise details about road conditions, helping them understand what to expect and how to respond appropriately. Common Mistakes to Avoid Ignoring the supplementary plate and only reading the main sign Misjudging the distance or duration of a hazard Failing to adjust speed based on full information Overlooking temporary or changing conditions Safety Tips Always read the full sign combination (main + supplementary plate) Adjust speed early when distance warnings are shown Stay alert for multiple signs in sequence Drive cautiously in unfamiliar or changing conditions Penalties for Ignoring the Sign Ignoring supplementary information may result in: Failure to respond correctly to road hazards Traffic fines for non-compliance with restrictions Increased risk of collisions or road incidents Liability in accidents due to negligence Summary The supplementary plate sign in South Africa provides important additional information about a main road sign. Drivers must read both signs together to understand hazards, distances, speeds, and conditions for safe driving.

Next to the entrance of a parking area or in the top right-hand or top lefthand corner of a notice board.

To inform you of the existence of an information office or notice board.

You can obtain information about the area at this sign.

Overview The Information Signs (South Africa) – Information Centre Sign is used to indicate the presence of an information office or notice board where road users and visitors can obtain local guidance or assistance. What the Sign Means This sign informs drivers and pedestrians that an official information point is available nearby. It is intended to help people find directions, local details, or assistance about the surrounding area. How It Works in Practice It marks the location of an information office or kiosk. It may also point to a notice board with local information. It helps visitors orient themselves in unfamiliar areas. Staff or posted notices provide guidance and directions. Driver Responsibilities Use the information centre if you need directions or assistance Park safely if stopping at the facility Follow any instructions provided by signage or staff Be mindful of pedestrians around the area Where You Will See This Sign This sign is commonly found: At tourist attractions and rest areas Near parking facilities and transport hubs At visitor centres in towns or parks On notice boards or information kiosks Purpose of the Sign The purpose of the information centre sign is to guide road users and visitors to a central point where they can access helpful information about the area, improving navigation and visitor experience. Common Mistakes to Avoid Driving past without using available assistance when needed Stopping in unsafe areas near the information point Confusing the sign with regulatory or warning signage Ignoring posted local instructions or notices Safety Tips Use the information centre when travelling in unfamiliar areas Park only in designated areas before seeking assistance Be aware of pedestrians and other visitors nearby Follow all posted local guidance carefully Summary The information centre sign in South Africa indicates a place where road users can obtain local information or assistance. It helps improve navigation and supports safe and informed travel.

On the left-hand side of the carriageway before an intersection.

To inform you that the traffic signals on this route are co-ordinated and that the signals will be green at all the subsequent intersections if you maintain the indicated speed.

If possible maintain the recommended speed. However, make sure that it is safe to enter every intersection and look out for drivers that do not yield. The speed indicated is a recommendation and not a speed limit.

Overview The Information Signs (South Africa) – Co-ordinated Traffic Signal Sign are placed on the left-hand side of the road before intersections where traffic lights are electronically synchronised along a route. What the Sign Means This sign indicates that multiple traffic signals along the route are coordinated (linked together). If a driver maintains the recommended speed, they are more likely to encounter green lights at successive intersections. The key purpose is: to inform drivers that traffic lights are coordinated and that maintaining a recommended speed may allow smoother travel through multiple green signals. How It Works in Practice Traffic signals along the route operate in a timed sequence. Driving at the recommended speed improves the chance of hitting green lights. The system is designed to improve traffic flow and reduce stopping. Conditions can still change due to traffic or pedestrian demand. Driver Responsibilities Maintain the recommended speed where safe to do so Do not exceed legal speed limits Be prepared to stop at any intersection if needed Check for vehicles or pedestrians that may not obey signals Where You Will See This Sign Urban arterial roads with multiple traffic lights City corridors designed for traffic flow coordination Busy commuter routes Areas using “green wave” traffic systems Purpose of the Sign The coordinated traffic signal sign helps improve traffic efficiency by encouraging steady driving speeds that align with synchronized traffic lights, reducing unnecessary stops and congestion. Common Mistakes to Avoid Speeding to “catch” green lights Assuming all intersections will always remain green Ignoring pedestrians or cross traffic at intersections Treating the recommended speed as a legal limit Safety Tips Maintain a smooth, steady driving speed Always be ready to stop at intersections Watch for changing signals and road users Prioritise safety over maintaining timing with lights Penalties for Ignoring the Sign Ignoring traffic signal conditions may result in: Red-light violations at intersections Collisions with crossing vehicles or pedestrians Traffic fines for speeding or unsafe driving Increased risk of intersection accidents Summary The coordinated traffic signal sign in South Africa indicates that traffic lights along a route are synchronised. Drivers should maintain a safe recommended speed, but always remain alert and ready to stop at any intersection if required.

At intersections at the same pole as traffic signals (robot) under signal head.

To point out that the signals at this intersection does not follow the normal sequence. At a normal intersection you would expect that the signal in your direction will change to green after the signal for cross traffic was yellow. At this intersection your signal may remain red whilst the signal in the opposite direction changes to green.

Do not move off when approaching traffic moves off. Wait until the signal is green. The sequence of the traffic signals at this intersection can be different during normal and during peak times.

Overview The Information Signs (South Africa) – Multi-Phase Traffic Signal Sign is installed at intersections on the same pole as traffic lights to warn drivers that the traffic signal phases at that junction do not follow the normal sequence. What the Sign Means This sign explains that the traffic light system at the intersection operates in multiple phases, meaning the signal changes may differ from what drivers normally expect. For example, your direction may remain red while another direction turns green, even if cross traffic is moving. How It Works in Practice Traffic lights operate in more than the standard two-phase system. Different directions may receive green lights at different times. Signal timing may change between normal and peak traffic periods. Drivers cannot assume movement based on other vehicles. Driver Responsibilities Wait for your own signal to turn green before moving Do not follow other vehicles blindly when they move off Pay close attention to the traffic light facing your lane Be alert for unusual signal sequences at busy intersections Where You Will See This Sign This sign is commonly found: At busy urban intersections with complex traffic flow Where traffic lights are timed for multiple phases At intersections with turning or dedicated lanes In areas with peak-hour traffic adjustments Purpose of the Sign The purpose of the multi-phase traffic signal sign is to prevent confusion and unsafe driving by informing motorists that traffic light sequences may not follow the standard pattern, reducing the risk of collisions at intersections. Common Mistakes to Avoid Moving off when other vehicles begin moving Assuming the signal will turn green in a predictable sequence Ignoring the traffic light facing your lane Rushing through intersections during phase changes Safety Tips Focus only on your own traffic signal Wait for a clear green signal before moving Expect unusual timing during peak hours Proceed cautiously even when signals change Summary The multi-phase traffic signal sign in South Africa warns drivers that traffic lights at the intersection may operate in a non-standard sequence. Drivers must wait for their own green light and avoid following other vehicles prematurely.

On the left-hand side of any road.

To show that there is a transport modal transfer point or terminus nearby where passengers may change their mode of transport.

Make sure that it is safe to slow down and stop to drop someone off or pick someone up. Also look out for pedestrians who may cross the road.

Overview The Information Signs (South Africa) – Modal Transfer Sign are placed on the left-hand side of roads to indicate the presence of a nearby transport interchange or terminus where passengers can change from one form of transport to another. What the Sign Means This sign informs drivers that they are approaching a location where different transport modes connect, such as buses, taxis, trains, or minibuses, and where passengers frequently board, alight, or transfer. The key purpose is: to indicate a nearby transport transfer point and alert drivers to increased pedestrian and passenger activity. How It Works in Practice The area may include bus stops, taxi ranks, or train stations. There is often high pedestrian movement near the road. Vehicles may stop frequently to pick up or drop off passengers. Traffic flow may be slower due to frequent stops. Driver Responsibilities Reduce speed when approaching the area Be prepared to stop safely for passengers Watch carefully for pedestrians crossing the road Ensure stopping or parking does not obstruct traffic Where You Will See This Sign Near bus terminals and taxi ranks At railway or commuter train stations In urban transport hubs Along busy commuter routes with frequent passenger transfers Purpose of the Sign The modal transfer sign improves road safety by warning drivers of high pedestrian activity and frequent stopping points where passengers move between different transport systems. Common Mistakes to Avoid Driving at high speed through busy transfer areas Failing to expect sudden stops by other vehicles Ignoring pedestrians crossing between transport points Stopping in unsafe or obstructive locations Safety Tips Slow down early when approaching transport hubs Scan for pedestrians and stopped vehicles Only stop when it is safe and legal to do so Maintain extra caution during peak commuting times Penalties for Ignoring the Sign Ignoring modal transfer area warnings may result in: Collisions with pedestrians or passengers Traffic fines for unsafe stopping or driving Obstruction of public transport flow Liability for accidents in high-risk zones Summary The modal transfer sign in South Africa alerts drivers to nearby transport hubs where passengers frequently change transport modes. Drivers must slow down, stay alert for pedestrians, and stop safely when necessary.

On the left-hand side of the road.

To inform you of a temporary experiment or research being carried out on the road.

Look out for vehicles, pedestrians and other hazards engaged in the experiment.

Overview The Information Sign – Road Experiment in South Africa is a temporary informational road sign placed on the left-hand side of the road. It informs road users that a controlled traffic experiment, study, or research activity is taking place in the area. What the Sign Means This sign indicates that road authorities or researchers are conducting a temporary experiment on or near the roadway. Drivers should be aware that unusual traffic behaviour, markings, or pedestrian activity may be present. How It Works in Practice Alerts drivers to a temporary road-based research activity. May involve changes to normal traffic flow or road use. Could include pedestrians, cyclists, or controlled vehicle tests. Requires increased caution and observation from all road users. Driver Responsibilities Reduce speed when approaching the experimental area Be alert for unusual road conditions or markings Watch for pedestrians, cyclists, or test vehicles Follow any instructions from traffic officials or signage Where You Will See This Sign This sign is commonly found: In urban or suburban research zones Near universities or transport study areas On roads undergoing safety or traffic flow testing At temporary trial intersections or lane configurations Purpose of the Sign The purpose of the road experiment information sign is to ensure road users are aware of ongoing studies or trials, improving safety and reducing confusion while traffic data or new road systems are being tested. Common Mistakes to Avoid Driving at normal speed without noticing the experiment zone Ignoring unusual road layouts or markings Assuming standard traffic rules fully apply without change Failing to watch for pedestrians or test participants Safety Tips Slow down and stay alert when entering the area Expect unexpected movements from other road users Follow temporary instructions carefully Maintain a safe following distance at all times Penalties and Risks for Ignoring Guidance Ignoring this sign may result in: Accidents involving pedestrians or test participants Interference with official traffic studies Traffic fines for unsafe driving behaviour Increased risk of collisions due to unusual road conditions Summary The road experiment information sign in South Africa alerts drivers to temporary research or testing activities on the road, requiring extra caution due to unusual traffic conditions and potential hazards.