On any road where slow-moving vehicles could disrupt the traffic flow.

To regulate the minimum speed of traffic.

This is a minimum speed sign. You must travel at this speed or faster.

Overview The Minimum Speed Sign in South Africa is a regulatory command sign used to indicate the lowest legal speed at which vehicles must travel on a specific section of road. It is designed to ensure that traffic flows smoothly and that slow-moving vehicles do not cause unnecessary congestion or hazards. What the Sign Means When a driver sees this sign, it means they must not travel below the indicated minimum speed unless road, traffic, or weather conditions make it unsafe to do so. It applies to all vehicles using that section of road. The key rule is: do not drive slower than the indicated minimum speed unless necessary for safety. Driver Responsibilities Maintain at least the posted minimum speed when conditions allow Avoid unnecessary slow driving that may disrupt traffic flow Increase speed appropriately when entering such roads if safe Reduce speed only when road, traffic, or weather conditions require it Where You Will See This Sign This sign is commonly placed: On highways and freeways On high-speed arterial roads In areas where slow-moving vehicles could create danger Near tunnels, bridges, or controlled-access roads Why the Sign Is Important The Minimum Speed Sign helps prevent traffic congestion and reduces the risk of rear-end collisions caused by overly slow vehicles. It ensures a consistent and predictable flow of traffic, especially on high-speed roads. Common Mistakes to Avoid Driving significantly below the minimum speed without reason Ignoring traffic flow conditions while trying to maintain minimum speed Assuming the rule applies even in unsafe conditions (such as heavy rain or fog) Confusing minimum speed with recommended speed Safety Tips Always adjust speed according to road conditions Maintain awareness of surrounding traffic flow Increase speed gradually when entering highways Use caution in poor visibility or adverse weather Penalties for Ignoring the Sign Failing to comply with a Minimum Speed Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions and traffic disruption Summary The Minimum Speed Sign in South Africa regulates the lowest allowable speed on certain roads to maintain safe and efficient traffic flow. Drivers must comply unless conditions make it unsafe, ensuring smoother and safer travel for all road users.

On any public road.

To compel drivers of certain heavy vehicles to use the road or part of the road indicated by this road traffic sign.

Vehicles exceeding GVM shown must use only this part of the roadway. No other road users may.

Overview The Vehicles Exceeding Mass Only Sign in South Africa is a regulatory command sign used to control the movement of heavy vehicles on public roads. It instructs drivers of vehicles above a specified mass limit to use a designated road or section of road. What the Sign Means When a driver sees this sign, it means that only vehicles exceeding the stated mass (typically heavy trucks or freight vehicles) are required to use the indicated route. Lighter vehicles must use alternative routes where applicable. The key rule is: heavy vehicles must follow the designated route shown by the sign. Driver Responsibilities Check your vehicle’s mass classification before entering the road Follow the route indicated if your vehicle exceeds the stated mass Avoid using restricted roads not designated for heavy vehicles Comply with all additional signage along the route Where You Will See This Sign This sign is commonly placed: On national and provincial roads with heavy vehicle routing controls Near industrial zones and freight corridors At road access points where structural load limits exist On alternative routes designed for trucks and heavy transport Purpose of the Sign The Vehicles Exceeding Mass Only Sign is used to protect road infrastructure and improve traffic safety. It ensures that heavy vehicles are directed to roads built to handle their weight, reducing damage to lighter roads and improving overall traffic management. Common Mistakes to Avoid Ignoring mass restrictions and entering prohibited roads Misjudging vehicle weight and using unsuitable routes Assuming all roads are suitable for heavy vehicles Failing to follow designated freight routes Safety Tips Know your vehicle’s loaded and unloaded mass limits Plan routes in advance for heavy transport vehicles Follow signage carefully, especially in urban areas Drive cautiously on roads designated for heavy traffic Penalties for Ignoring the Sign Disobeying this sign is a traffic offence and may result in: Fines Legal liability for road damage Vehicle restrictions or enforcement action Increased risk of accidents or infrastructure damage Summary The Vehicles Exceeding Mass Only Sign in South Africa directs heavy vehicles to use specific roads designed for their weight. Following this sign helps protect road infrastructure and ensures safer, more efficient transport operations.

At obstructions such as traffic islands. Only one of these signs will be displayed at a time.

To indicate that you must drive to the left or right of an obstruction where the sign is displayed.

You must pass to the side indicated by the angled arrow.

Overview The Keep Left Sign (Command Sign) in South Africa is a regulatory road sign used to instruct drivers to pass to the left side of a physical obstruction on the roadway. It is commonly placed where traffic must be guided safely around islands, barriers, or other obstructions. What the Sign Means When a driver sees this sign, it means they must pass to the left side of the obstruction directly ahead. It ensures that traffic flows safely and consistently around fixed road features. The key rule is: keep left of the obstruction and follow the indicated direction. Driver Responsibilities Drive to the left side of the obstruction shown Follow the directional instruction without deviation Slow down when approaching traffic islands or barriers Remain alert for other vehicles doing the same manoeuvre Where You Will See This Sign This sign is commonly placed: At traffic islands in the middle of roads At roadworks or temporary lane diversions At split lanes or narrowed sections of road Where permanent or temporary obstacles are present Why the Sign Is Important The Keep Left Sign helps prevent collisions by clearly directing traffic around obstructions. It improves road safety and ensures smooth traffic flow in areas where the normal lane path is blocked or altered. Common Mistakes to Avoid Passing on the wrong side of the obstruction Ignoring directional instructions in roadworks Driving too fast around traffic islands Assuming the obstruction can be passed on either side Safety Tips Slow down as soon as you approach the sign Observe the obstruction and plan your path early Follow lane markings in addition to signage Stay alert for pedestrians and cyclists near islands Penalties for Ignoring the Sign Ignoring a Keep Left Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions or liability in accidents Summary The Keep Left Sign in South Africa directs drivers to pass to the left of an obstruction such as a traffic island. Following this command sign is essential for safe navigation and preventing road accidents.

At obstructions such as traffic islands. Only one of these signs will be displayed at a time.

To indicate that you must drive to the left or right of an obstruction where the sign is displayed.

You must pass to the side indicated by the angled arrow.

Overview The Keep Right Sign in South Africa is a regulatory command sign used to instruct drivers to pass to the right of an obstruction such as a traffic island, roadworks barrier, or divider. It is typically used in combination with a “Keep Left” sign, but only one will be displayed depending on the direction traffic must follow. What the Sign Means When a driver sees this sign, they must drive to the right side of the obstruction shown ahead. It indicates the correct side to pass safely around a physical barrier or traffic island. The key rule is: always pass to the right of the obstruction where indicated. Driver Responsibilities Follow the direction indicated by the sign without hesitation Pass traffic islands or obstructions on the right side only Stay within lane markings leading up to the obstruction Reduce speed when approaching the sign Where You Will See This Sign This sign is commonly found: At traffic islands and painted or physical road dividers At roadworks and temporary lane diversions At intersections with channelised traffic flow Where road layout requires vehicles to be directed around an obstacle Purpose of the Sign The Keep Right Sign is used to clearly indicate the safe and correct direction of travel around an obstruction. It helps prevent confusion, avoids head-on conflicts, and ensures smooth traffic movement in constrained road spaces. Common Mistakes to Avoid Passing on the wrong (left) side of the obstruction Ignoring the sign in low-traffic situations Changing lanes suddenly near the obstacle Assuming both sides of the obstruction are allowed Safety Tips Slow down when approaching traffic islands or roadworks Follow road markings in addition to signage Stay alert for pedestrians and construction workers Maintain safe following distances in diverted lanes Penalties for Ignoring the Sign Disobeying a Keep Right Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions and liability Summary The Keep Right Sign in South Africa directs drivers to pass to the right of an obstruction. It is a simple but important command that ensures safe, predictable movement around traffic islands and road hazards.

At intersections.

To indicate the direction in which you must proceed.

You must proceed only in the direction of the arrow.

Overview The Proceed Left Only Sign in South Africa is a regulatory command sign found at intersections. It instructs drivers that they must turn or continue only in the left direction when reaching the intersection. It is used to control traffic flow and prevent unsafe or illegal turning movements. What the Sign Means When a driver sees this sign, they are required to proceed only to the left at the intersection. Driving straight or turning right is not permitted. The key rule is: you must turn or move left only. Driver Responsibilities Follow the instruction to turn left at the intersection Do not proceed straight or turn right Signal early before making the left turn Yield to pedestrians and oncoming traffic where required Where You Will See This Sign This sign is commonly placed: At intersections with restricted movement In one-way traffic systems Near roadworks or temporary traffic diversions In areas where only left turns are allowed for safety or flow control Purpose of the Sign The Proceed Left Only Sign is used to direct vehicles safely and efficiently through intersections. It helps reduce congestion, prevents conflicting traffic movements, and improves overall road safety. Common Mistakes to Avoid Driving straight through the intersection Turning right instead of left Ignoring lane markings and signal instructions Failing to check for pedestrians before turning Safety Tips Slow down when approaching intersections with command signs Check mirrors and blind spots before turning Use indicators early to signal your intention Watch for pedestrians and cyclists crossing the road Penalties for Ignoring the Sign Disobeying a Proceed Left Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions and legal liability Summary The Proceed Left Only Sign in South Africa is a command sign that requires drivers to turn or proceed only to the left at an intersection. Following this instruction ensures safer intersections and smoother traffic flow.

At intersections.

To indicate the direction in which you must proceed.

You must proceed only in the direction of the arrow.

Overview The Proceed Right Only Sign in South Africa is a regulatory command sign that is used at intersections to instruct drivers that they must turn or proceed only to the right. It is part of a group of mandatory direction signs that control traffic movement and improve safety at junctions. What the Sign Means When this sign is displayed, drivers are required to move only in the right-hand direction at the intersection. Continuing straight or turning left is not permitted. The key rule is: you must only proceed to the right. Driver Responsibilities Follow the mandatory instruction to turn right Do not proceed straight through the intersection Do not turn left where the sign is displayed Signal clearly before making the right turn Where You Will See This Sign This sign is commonly found: At intersections where traffic must be directed right At roadworks or temporary traffic diversions At exits of one-way streets or controlled junctions In areas where traffic flow is restricted for safety or planning reasons Purpose of the Sign Command signs like the Proceed Right Only Sign are used to indicate the direction in which drivers must travel. They help regulate traffic flow, reduce confusion, and prevent conflicting movements at intersections. Why the Sign Is Important This sign improves road safety by ensuring all vehicles follow a single controlled direction at specific points. It helps prevent collisions caused by incorrect turning decisions and maintains orderly traffic movement. Common Mistakes to Avoid Driving straight through the intersection Turning left instead of right Ignoring accompanying lane markings or signals Failing to signal before turning right Safety Tips Slow down when approaching intersections with command signs Check for pedestrians before turning right Use indicators early and clearly Follow all road markings in addition to signage Penalties for Ignoring the Sign Ignoring a Proceed Right Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions and legal liability Summary The Proceed Right Only Sign in South Africa is a command sign found at intersections that directs drivers to proceed only to the right. It ensures safe, controlled, and predictable traffic movement.

At intersections.

To indicate the direction in which you must proceed.

You must proceed only in the direction of the arrow.

Overview The Proceed Straight Only Sign in South Africa is a regulatory (command) road sign used at intersections. It instructs drivers that they must continue driving straight ahead and are not permitted to turn left or right. What the Sign Means When this sign is displayed, drivers are required to proceed straight through the intersection in the direction indicated. Any turning movement is prohibited at that point. The key rule is: you must continue straight ahead only. Driver Responsibilities Continue straight through the intersection Do not turn left or right where the sign applies Follow lane markings that support the straight movement Signal only if changing lanes (not for turning) Where You Will See This Sign This sign is commonly found: At controlled intersections In roadworks or temporary traffic diversions At entrances to one-way or restricted-flow roads Where turning movements are unsafe or not allowed Purpose of the Sign The purpose of the Proceed Straight Only Sign is to clearly indicate the permitted direction of travel at an intersection. It helps regulate traffic flow, prevent confusion, and reduce the risk of collisions caused by conflicting turning movements. Common Mistakes to Avoid Turning left or right at the intersection Ignoring lane markings that enforce straight movement Entering the wrong lane too close to the intersection Assuming turning is allowed if the road appears open Safety Tips Slow down when approaching intersections Check road markings in advance to position correctly Be alert for pedestrians crossing Follow all additional signage and signals Penalties for Ignoring the Sign Ignoring a Proceed Straight Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of accidents and liability Summary The Proceed Straight Only Sign in South Africa is a command sign that requires drivers to continue straight through an intersection. It ensures clear direction control, improves traffic flow, and reduces the risk of collisions.

At intersections.

To indicate to drivers the direction in which they must turn at the intersection ahead.

You must turn in the direction of the arrow at the next junction.

Overview The Turn Left Sign (Command Sign) in South Africa is a regulatory road sign found at or approaching intersections. It instructs drivers that they must turn left at the intersection ahead. This sign is part of a group of mandatory direction signs used to control vehicle movement and ensure safe traffic flow. What the Sign Means When a driver sees this sign, they are required to turn left at the upcoming intersection. Continuing straight or turning right is not permitted. The key rule is: you must turn left at the intersection ahead. Purpose of the Sign The purpose of the Turn Left Command Sign is to indicate to drivers the exact direction in which they must turn at the intersection ahead. It helps regulate traffic flow and prevents conflicting movements that could lead to congestion or accidents. Driver Responsibilities Prepare to turn left when approaching the intersection Do not proceed straight through the junction Do not turn right where the sign is displayed Signal in advance before turning left Where You Will See This Sign At intersections with controlled turning movements In roadworks or temporary traffic management zones At entrances to one-way systems or restricted roads Where traffic flow must be directed for safety or efficiency Why the Sign Is Important This sign ensures that all drivers follow a predictable route through intersections. It reduces confusion, prevents head-on or crossing conflicts, and improves overall road safety. Common Mistakes to Avoid Driving straight instead of turning left Turning right against the instruction Ignoring accompanying road markings Failing to signal before turning Safety Tips Slow down when approaching the intersection Check for pedestrians before turning Use indicators early and clearly Follow all additional signage and lane markings Penalties for Ignoring the Sign Disobeying a Turn Left Command Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions and legal consequences Summary The Turn Left Command Sign in South Africa indicates that drivers must turn left at the intersection ahead. It plays an important role in controlling traffic direction and maintaining safe, orderly road use.

At intersections.

To indicate to drivers the direction in which they must turn at the intersection ahead.

You must turn in the direction of the arrow at the next junction.

Overview The Turn Right Sign in South Africa is a regulatory command sign that instructs drivers to turn right at the intersection ahead. It is used to control traffic flow and ensure vehicles follow a designated direction safely and consistently. What the Sign Means When this sign is displayed, drivers are required to turn right only when they reach the intersection. Continuing straight or turning left is not permitted at that point. The key rule is: you must turn right at the intersection ahead. Driver Responsibilities Prepare early to move into the correct lane for a right turn Do not proceed straight through the intersection Do not turn left where the sign applies Signal clearly before making the right turn Where You Will See This Sign This sign is commonly found: At intersections with restricted turning options In roadworks or temporary traffic diversion areas At exits of one-way streets In areas where traffic must be directed along a specific route Purpose of the Sign The purpose of the Turn Right Sign is to indicate to drivers the direction in which they must turn at the intersection ahead. It helps manage traffic movement, reduce confusion, and prevent conflicting vehicle paths. Common Mistakes to Avoid Driving straight through the intersection Turning left instead of right Ignoring lane markings that reinforce the instruction Failing to signal before turning Safety Tips Slow down as you approach the intersection Check for pedestrians and cyclists before turning Use your indicator early and clearly Follow all road markings and additional signage Penalties for Ignoring the Sign Ignoring a Turn Right Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions and legal consequences Summary The Turn Right Sign in South Africa is a command sign that instructs drivers to turn right at the intersection ahead. Following this instruction ensures safer intersections and smoother traffic flow.

At the beginning of any road or part of a road.

To indicate that the road or part of the road may be used by pedestrians only.

Pedestrians must use only this part of the roadway. No other road users may use this part of the road.

Overview The Pedestrians Only Sign in South Africa is a command (regulatory) road sign that indicates a road or section of road is reserved exclusively for pedestrian use. It prohibits all forms of vehicle traffic, ensuring a safe and dedicated space for walking. What the Sign Means When this sign is displayed, only pedestrians are allowed to use the road or section of road. Motor vehicles, motorcycles, bicycles, and other forms of transport are not permitted. The key rule is: this area is for pedestrians only. Driver Responsibilities Do not enter pedestrian-only zones with any vehicle Respect barriers or markings indicating pedestrian areas Look for alternative routes for vehicles Be especially cautious near pedestrian entrances and crossings Where You Will See This Sign This sign is commonly placed: At the entrances of pedestrian malls or walkways In shopping districts or city centres Inside parks, promenades, or recreational areas On streets temporarily or permanently closed to vehicles Purpose of the Sign The Pedestrians Only Sign is used to create safe walking environments by eliminating vehicle access. It reduces the risk of accidents, improves pedestrian comfort, and promotes walkable public spaces. Common Mistakes to Avoid Driving or riding a vehicle into a pedestrian-only zone Assuming delivery access is always permitted Ignoring temporary pedestrian-only restrictions Using bicycles or scooters where they are not allowed Safety Tips Always check signage before entering a street or walkway Use designated vehicle routes around pedestrian zones Drive slowly near entrances to pedestrian areas Watch for pedestrians crossing at nearby access points Penalties for Ignoring the Sign Entering a Pedestrians Only area with a vehicle is a traffic offence and may result in: Fines Demerit points (where applicable) Risk of pedestrian injury and legal liability Summary The Pedestrians Only Sign in South Africa designates a road or area exclusively for pedestrian use. It helps create safe, vehicle-free spaces and protects pedestrians from traffic-related hazards.

At the beginning of any road or part of a road.

To indicate that the road or part of the road may be used by cyclists only.

Pedal cyclists must use only this part of the roadway. No other road users may use this part of the road.

Overview The Pedal Cycles Only Sign in South Africa is a regulatory command sign that indicates a road or section of road is reserved exclusively for cyclists. It is used to create safe cycling routes by prohibiting all other forms of traffic. What the Sign Means When this sign is displayed, only pedal cycles (bicycles) are allowed to use the road or designated section. Motor vehicles, motorcycles, and pedestrians are not permitted unless specifically indicated by additional signage. The key rule is: this road is for cyclists only. Driver Responsibilities Do not enter or drive into cycle-only lanes or roads Respect barriers or markings indicating cycling routes Look for alternative routes for motor vehicle travel Be cautious near cycle-only entrances and crossings Where You Will See This Sign This sign is commonly placed: At the beginning of dedicated cycle lanes or cycle tracks Within cycling routes in parks or recreational areas In urban cycling networks and green transport corridors At access points where only bicycles are permitted Why the Sign Is Important The Pedal Cycles Only Sign helps improve cyclist safety by separating bicycles from motor vehicle traffic. It encourages cycling as a safe and sustainable mode of transport while reducing accident risk. Common Mistakes to Avoid Driving a motor vehicle into a cycle-only lane Assuming short access is allowed for parking or drop-off Ignoring road markings that reinforce the restriction Confusing shared paths with cycle-only routes Safety Tips Always check signage before entering a narrow or dedicated lane Watch for cyclists when approaching cycle route entrances Use designated vehicle routes for access and delivery Drive slowly near cycling infrastructure zones Penalties for Ignoring the Sign Disobeying a Pedal Cycles Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of accidents and legal liability Summary The Pedal Cycles Only Sign in South Africa designates a road or section of road exclusively for bicycles. Following this rule ensures cyclist safety and supports organized traffic separation.

At the beginning of any road or part of the road.

To indicate that a road or part of a road may be used by cyclists and/or pedestrians only.

Pedal cyclists and pedestrians must use only this part of the roadway. No other road users may use this part of the road.

Overview The Pedal Cycles & Pedestrians Only Sign in South Africa is a regulatory command sign used to indicate that a specific road or section of road is reserved exclusively for non-motorised users. It allows only pedestrians and cyclists to use the designated area, improving safety and separating them from motor vehicle traffic. What the Sign Means When this sign is displayed, only pedestrians and pedal cyclists are permitted to use the road or pathway. Motor vehicles, motorcycles, and other motorised transport are strictly prohibited. The key rule is: this road is for pedestrians and cyclists only. Driver Responsibilities Do not enter or drive into pedestrian and cycle-only areas Look for alternative routes for motor vehicle travel Respect physical barriers and signage at entry points Be cautious near entrances where cyclists and pedestrians may cross Where You Will See This Sign This sign can be found: At the beginning of pedestrianised streets or zones Along shared-use paths for walking and cycling In parks, promenades, and recreational corridors In city centres with restricted vehicle access Purpose of the Sign The purpose of the Pedal Cycles & Pedestrians Only Sign is to indicate that a road or part of a road may be used only by pedestrians and cyclists. It enhances safety by removing motor vehicle traffic and creating a safer shared space for vulnerable road users. Common Mistakes to Avoid Driving or riding a motor vehicle into restricted zones Assuming short access is allowed for deliveries or drop-offs Ignoring entry barriers or additional warning signs Confusing shared pedestrian/cycle zones with general traffic roads Safety Tips Always check signage before entering urban or pedestrian areas Use designated access routes for vehicles Drive slowly near entrances to shared-use zones Watch for cyclists and pedestrians crossing near boundaries Penalties for Ignoring the Sign Ignoring this command sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of accidents and legal liability Summary The Pedal Cycles & Pedestrians Only Sign in South Africa designates roads or sections of roads exclusively for pedestrians and cyclists. It improves safety and ensures that vulnerable road users have protected spaces free from motor vehicles.

At the beginning of any road or part of the road.

To indicate that a road or part of a road may be used by cyclists and/or pedestrians only.

Pedal cyclists and pedestrians must use only this part of the roadway. No other road users may use this part of the road. This sign indicate that part of the road is divided and that part may be used by cyclists and pedestrians only.

Overview The Pedal Cycles & Pedestrians Only Command Sign in South Africa is a regulatory sign that indicates a road or section of road is reserved exclusively for pedestrians and/or cyclists. It prohibits all motorised vehicles from entering and is used to create safe, non-motorised transport corridors. What the Sign Means When this sign is displayed, the road or section ahead may only be used by pedestrians and pedal cyclists. Motor vehicles, motorcycles, and other motorised transport are not allowed to enter the area. The key rule is: this road is for pedestrians and cyclists only. Driver Responsibilities Do not enter roads marked with this command sign Look for alternative routes for motor vehicles Respect barriers, bollards, or markings indicating restricted access Be cautious near entrances to pedestrian and cycle zones Where You Will See This Sign According to its usage, this sign is typically found: At the beginning of any road or part of a road reserved for non-motorised use At entrances to pedestrian precincts or cycle-only routes In parks, promenades, or shared mobility corridors In areas designed for safe walking and cycling infrastructure Purpose of the Sign The purpose of the Pedal Cycles & Pedestrians Only Command Sign is to indicate that a road or section of road is intended exclusively for pedestrians and/or cyclists. It helps reduce vehicle-pedestrian conflicts and promotes safer, more sustainable transport environments. Why the Sign Is Important This sign improves safety by separating vulnerable road users from motor vehicle traffic. It also supports urban planning strategies that encourage walking and cycling in designated safe zones. Common Mistakes to Avoid Driving into pedestrian or cycle-only roads Assuming limited vehicle access is allowed without permission Ignoring entry barriers or clear signage Confusing shared-use paths with motor vehicle roads Safety Tips Always check signage before entering a road or pathway Use designated vehicle routes for all motorised travel Be alert near entrances to pedestrian and cycle zones Drive slowly in areas adjacent to these zones Penalties for Ignoring the Sign Ignoring a Pedal Cycles & Pedestrians Only Command Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Risk of accidents and legal liability Summary The Pedal Cycles & Pedestrians Only Command Sign in South Africa indicates that a road or section of road may only be used by pedestrians and cyclists. It is typically placed at the beginning of such roads and helps ensure safe, vehicle-free spaces for non-motorised users.

At the beginning of any road or part of the road.

To indicate that a road or part of a road may be used by cyclists and/or pedestrians only.

Pedal cyclists and pedestrians must use only this part of the roadway. No other road users may use this part of the road.

Overview The Pedal Cycles & Pedestrians Only Command Sign in South Africa is a regulatory sign used to indicate that a road or a section of road is reserved exclusively for pedestrians and cyclists. It clearly defines areas where motor vehicles are not permitted, ensuring safe shared use between walking and cycling traffic. What the Sign Means When this sign is displayed, the road or section of road may only be used by pedestrians and/or pedal cyclists. All motorised vehicles are prohibited unless specifically authorised by additional signage or exceptions. The key rule is: this road is for pedestrians and cyclists only. Driver Responsibilities Do not enter roads marked for pedestrians and cyclists only Respect physical barriers or controlled entry points Be alert for pedestrian and cycle crossings near access points Use alternative routes for motor vehicle travel Where You Will See This Sign This command sign is typically found: At the beginning of pedestrian-only streets or zones At entrances to cycle paths or shared pedestrian-cycle routes In city centres, malls, or pedestrian precincts At parks, promenades, and recreational corridors Purpose of the Sign The purpose of the Pedal Cycles & Pedestrians Only Command Sign is to clearly indicate that a road or section of road is reserved exclusively for non-motorised users. It helps improve safety, reduce vehicle-pedestrian conflict, and support walking and cycling as safe transport modes. Common Mistakes to Avoid Driving or riding motor vehicles into restricted pedestrian-cycle roads Assuming short access is allowed for deliveries without permission Ignoring entry signs at the start of pedestrian zones Confusing shared-use areas with normal traffic roads Safety Tips Always check signage before entering a road or pathway Plan alternative routes for motor vehicle access Be cautious near entrances where pedestrians and cyclists mix with traffic Respect barriers, bollards, and controlled entry points Penalties for Ignoring the Sign Ignoring this command sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of accidents and legal liability Summary The Pedal Cycles & Pedestrians Only Command Sign in South Africa indicates that a road or section of road is reserved exclusively for cyclists and pedestrians. It is typically placed at the beginning of such roads to clearly restrict motor vehicle access and ensure safe, non-motorised use.

At the beginning of any road or part of the road.

To indicate that a road or part of a road may be used by cyclists and/or pedestrians only.

Pedal cyclists and pedestrians must use only this part of the roadway. No other road users may use this part of the road. This sign indicate that part of the road is divided and that part may be used by cyclists and pedestrians only.

Overview The Pedal Cycles & Pedestrians Only Sign in South Africa is a regulatory command sign found at the beginning of a road or section of road. It indicates that the area is reserved exclusively for use by cyclists and pedestrians. What the Sign Means When this sign is displayed, only pedal cyclists and pedestrians are allowed to use the road or section of road ahead. All motorised vehicles are prohibited from entering or using the area unless specifically permitted by additional signage. The key rule is: this road or section is for cyclists and pedestrians only. Driver Responsibilities Do not enter roads or sections marked for pedestrians and cyclists only Plan alternative routes if approaching a restricted access point Be alert for signage indicating pedestrian and cycle zones Respect barriers, markings, and physical restrictions at entry points Where You Will See This Sign This sign can be found: At the beginning of pedestrianised streets or zones At entrances to cycle-only routes or paths In parks, promenades, or shared public spaces Within urban areas designed for non-motorised transport Purpose of the Sign The purpose of the Pedal Cycles & Pedestrians Only Sign is to indicate that a road or section of road is reserved exclusively for pedestrians and cyclists. It improves safety by eliminating motor vehicle traffic in areas designed for non-motorised use and supports safer, more accessible public environments. Common Mistakes to Avoid Driving into pedestrian or cycle-only roads Assuming limited access is allowed without checking signage Ignoring entry restrictions or barriers Confusing shared pedestrian zones with normal roads Safety Tips Always read signage before entering any unfamiliar road Slow down when approaching pedestrianised areas Look for alternative routes in advance Be alert for cyclists and pedestrians in surrounding areas Penalties for Ignoring the Sign Ignoring this command sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of accidents and legal consequences Summary The Pedal Cycles & Pedestrians Only Sign in South Africa designates a road or section of road for exclusive use by cyclists and pedestrians. It is placed at entry points to ensure motor vehicles do not enter restricted, non-motorised zones.

At the beginning of any road or part of a road.

Indicate that a road or part of a road may be used by motorcyclists only.

Motor cycles must use only this part of the roadway. No other road users may use this part of the road.

Overview The Motor Cycles Only Sign in South Africa is a regulatory command sign that indicates a road or section of road is reserved exclusively for motorcycles. It is used to separate motorcyclists from other road users and manage specialised traffic flow in certain areas. What the Sign Means When this sign is displayed, only motorcyclists are allowed to use the indicated road or section. All other vehicles, including cars, trucks, bicycles, and pedestrians, are not permitted unless specifically authorised by additional signage. The key rule is: this road or section is for motorcyclists only. Driver Responsibilities Do not enter motorcycle-only roads with any other type of vehicle Look for alternative routes before approaching the restricted area Observe all entry signage at the beginning of the road Respect lane markings and access controls Where You Will See This Sign This sign is commonly found: At the beginning of designated motorcycle lanes or routes In controlled traffic systems or specialised transport zones At restricted access roads for safety or event management In areas designed to separate motorcycles from other traffic types Why the Sign Is Important The Motor Cycles Only Sign helps improve safety by providing dedicated space for motorcycles, reducing conflicts with larger or slower vehicles. It also helps manage traffic efficiency in areas with high motorcycle usage or specific transport requirements. Common Mistakes to Avoid Entering motorcycle-only roads with a car or truck Assuming partial access is allowed without confirmation Ignoring entry signage at the start of the road Confusing motorcycle lanes with general traffic lanes Safety Tips Always check signage before entering any restricted road Be alert for sudden changes in lane designation Plan alternative routes in advance when restrictions apply Follow all additional road markings and control devices Penalties for Ignoring the Sign Ignoring a Motor Cycles Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of accidents and legal consequences Summary The Motor Cycles Only Sign in South Africa designates a road or section exclusively for motorcycles. Following this sign ensures safer, more organised traffic flow and reduces conflict between different vehicle types.

At the beginning of any road or part of the road.

Indicate that a road or part of a road may be used by motorcars only.

Motor cars must use only this part of the roadway. No other road users may use this part of the road.

Overview The Motor Cars Only Sign in South Africa is a regulatory (command) road sign that indicates a road or section of road is reserved exclusively for motor cars. It is used to restrict access and ensure that only permitted vehicle types use a specific roadway. What the Sign Means When this sign is displayed, only motor cars are allowed to use the road or section ahead. Other vehicles such as trucks, motorcycles, buses, and non-motorised transport may be prohibited unless additional signage allows access. The key rule is: this road may be used by motor cars only. Driver Responsibilities Ensure your vehicle qualifies as a motor car before entering Do not enter if you are driving a truck, bus, or restricted vehicle type Check for alternative routes if your vehicle is not permitted Obey all supporting traffic signs and road markings Where You Will See This Sign This sign is typically found: At the beginning of a road or section of road In residential or restricted-access areas On private or controlled-access roads In zones where traffic must be limited for safety or structural reasons Why the Sign Is Important The Motor Cars Only Sign helps control traffic composition on certain roads. It reduces congestion, protects infrastructure, and improves safety by limiting access to appropriate vehicles only. Common Mistakes to Avoid Entering the road with a restricted vehicle type (e.g., trucks or buses) Ignoring entry signage at the start of the road Assuming short access is allowed for delivery purposes Failing to check alternative routes in advance Safety Tips Always check vehicle restrictions before entering a road Plan alternative routes if driving a non-permitted vehicle Observe all additional regulatory signs in the area Drive cautiously in restricted-access zones Penalties for Ignoring the Sign Disobeying a Motor Cars Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Restricted access removal or enforcement action Summary The Motor Cars Only Sign in South Africa indicates that a road or section of road is reserved exclusively for motor cars. Following this restriction ensures proper traffic management and protects road safety and infrastructure.

At the beginning of any road or part of a road.

To indicate that the road or portion of the road is set aside for use by taxis.

Taxis must use only this part of the roadway. No other road users may use this part of the road.

Overview The Taxis Only Sign in South Africa is a regulatory command sign that indicates a road or section of road is reserved exclusively for minibus taxis. It is used to manage public transport movement, improve traffic flow, and provide dedicated space for taxi operations. What the Sign Means When this sign is displayed, only licensed taxis are allowed to use the designated road or portion of road. All other vehicles, including private cars, motorcycles, and heavy vehicles, are not permitted to enter unless specifically authorised. The key rule is: this road or section is set aside for taxis only. Driver Responsibilities Do not enter taxi-only lanes or roads with a private vehicle Look for alternative routes if the road is restricted Be alert for taxis merging in and out of dedicated lanes Respect markings and signage indicating restricted public transport use Where You Will See This Sign This sign is commonly found: At the beginning of roads or road sections reserved for taxis In busy urban transport corridors Near taxi ranks and public transport hubs Along dedicated public transport priority routes Purpose of the Sign The Taxis Only Sign is used to provide dedicated road space for minibus taxis, which are a major form of public transport in South Africa. It helps improve efficiency, reduce congestion, and ensure safer and more organised taxi operations. Common Mistakes to Avoid Driving a private vehicle in a taxi-only lane or road Using the route as a shortcut during traffic congestion Ignoring lane markings and taxi-only symbols Entering restricted areas without checking signage Safety Tips Always check road signs before entering dedicated transport lanes Be cautious around taxi ranks and busy public transport areas Expect frequent stopping and merging of taxis in these zones Follow all traffic control signs and markings carefully Penalties for Ignoring the Sign Ignoring a Taxis Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Increased risk of collisions and legal consequences Summary The Taxis Only Sign in South Africa reserves specific roads or sections for minibus taxis only. Respecting it helps maintain efficient public transport systems and improves overall traffic management.

At the beginning of any road or part of a road.

Indicates that the road or a portion of the road is set aside for use by minibuses.

Minibuses must use only this part of the roadway. No other road users may use this part of the road.

Overview The Minibuses Only Sign in South Africa is a regulatory command sign that indicates a road or a specific portion of a road is reserved exclusively for minibuses, typically used for public transport such as taxi services. It is used to prioritise high-occupancy passenger transport and improve the efficiency of public transport systems. What the Sign Means When this sign is displayed, only minibuses are permitted to enter and use the designated road or lane. All other vehicles, including private cars, motorcycles, buses (unless specifically allowed), and trucks, are not permitted to use the restricted section. The key rule is: this road or lane is reserved for minibuses only. Driver Responsibilities Do not enter or drive in minibus-only lanes or roads with other vehicle types Check signage at the start of the road before proceeding Be alert for minibuses entering or exiting dedicated routes Follow alternative routes if you are not driving a minibus Where You Will See This Sign This sign is typically found: At the beginning of dedicated public transport routes Near taxi and minibus transport corridors In busy urban areas with high passenger transport demand At entrances to restricted or priority transport roads Why the Sign Is Important The Minibuses Only Sign helps improve public transport efficiency by giving minibuses dedicated access routes. This reduces congestion, improves travel times for commuters, and supports safer traffic management in busy areas. Common Mistakes to Avoid Entering a minibus-only road with a private vehicle Ignoring command signage at the start of restricted roads Using the lane as a shortcut during traffic congestion Failing to check road classification before entering Safety Tips Always read signage at the start of any road carefully Look for additional markings confirming vehicle restrictions Be cautious near minibus routes and taxi corridors Plan alternative routes if you are not permitted to enter Penalties for Ignoring the Sign Ignoring a Minibuses Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Legal consequences and disruption to public transport operations Summary The Minibuses Only Sign in South Africa designates specific roads or lanes exclusively for minibus public transport. Following it ensures efficient transport flow and supports safe, organised road use.

At the beginning of any road or part of a road.

Indicates that the road or a portion of the road is set aside for use by midibuses.

Midi buses must use only this part of the roadway. No other road users may use this part of the road.

Overview The Midibus Only Sign in South Africa is a regulatory command sign that indicates a road or section of road is reserved exclusively for midibuses. It is used to prioritise medium-sized public transport vehicles and improve the efficiency of passenger transport systems. What the Sign Means When this sign is displayed, only midibuses are allowed to enter and use the designated road or portion of road. All other vehicles, including private cars, minibuses, trucks, motorcycles, and buses (unless specifically authorised), are not permitted. The key rule is: this road or lane is set aside for midibuses only. Driver Responsibilities Do not enter midibus-only roads or lanes with any unauthorised vehicle Check signage carefully at the start of every restricted road section Be alert for midibuses entering or exiting the dedicated route Follow alternative routes if you are not driving a midibus Where You Will See This Sign This sign is typically found: At the beginning of roads or restricted road sections In dedicated public transport corridors Near transport hubs or commuter routes In areas where specific public transport systems are prioritised Why the Sign Is Important The Midibus Only Sign helps improve public transport efficiency by separating midibuses from general traffic. It ensures smoother passenger movement, reduces congestion, and supports organised transport systems in busy areas. Common Mistakes to Avoid Entering a midibus-only road with a private vehicle Ignoring signage at the start of restricted road sections Using the lane as a shortcut during congestion Failing to observe road markings supporting the restriction Safety Tips Always read entry signage before entering a road or lane Be cautious near public transport corridors Look out for midibuses merging into or exiting traffic Follow all alternative route signage if access is restricted Penalties for Ignoring the Sign Ignoring a Midibus Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Risk of collisions and disruption to public transport operations Summary The Midibus Only Sign in South Africa designates a road or portion of road exclusively for midibus use. Following it ensures efficient public transport flow and safer, more organised traffic management.

At the beginning of any road or part of a road.

Indicates that the road or a portion of the road is set aside for use by buses.

Buses must use only this part of the roadway. No other road users may use this part of the road.

Overview The Buses Only Sign (Command Sign) in South Africa is a regulatory road sign that indicates a road or a specific section of road is reserved exclusively for buses. It is typically placed at the beginning of the restricted section to clearly define the start of the bus-only route. What the Sign Means When this sign is displayed, only buses are allowed to travel on that road or portion of road. All other vehicles, including private cars, taxis, motorcycles, and trucks, are not permitted unless specifically authorised by additional signage. The key rule is: this road or section is set aside for buses only. Driver Responsibilities Do not enter or drive on bus-only roads or lanes Be alert for buses entering or exiting the restricted section Observe all markings that indicate the start and end of the bus-only zone Use alternative routes when approaching restricted bus corridors Where You Will See This Sign This sign is commonly placed: At the beginning of dedicated bus lanes or corridors In urban public transport priority systems Near bus terminals and transport hubs On sections of road reserved for high-capacity public transport Why the Sign Is Important The Buses Only Sign improves public transport efficiency by giving buses dedicated road space. It reduces congestion, improves travel times for commuters, and enhances road safety by separating large passenger vehicles from general traffic. Common Mistakes to Avoid Driving into bus-only lanes or roads Using bus lanes to bypass traffic congestion Ignoring entry signage at the start of restricted sections Assuming taxis or private vehicles are allowed without checking signage Safety Tips Always check for “bus only” signs before entering a road Watch for buses merging into or out of dedicated lanes Do not stop or park in bus-only areas Follow all road markings and public transport control signs Penalties for Ignoring the Sign Ignoring a Buses Only Sign is a traffic offence and may result in: Fines Demerit points (where applicable) Disruption of public transport operations and increased safety risks Summary The Buses Only Sign in South Africa marks roads or sections reserved exclusively for buses. Following it ensures efficient public transport operations and safer traffic management.

At the beginning of any road or part of a road.

Indicates that the road or a portion of the road is set aside for use by delivery vehicles only.

Delivery vehicles must use only this part of the roadway. No other road users may use this part of the road.

Overview The Delivery Vehicles Only Sign in South Africa is a regulatory command sign used to indicate that a specific road or section of road is reserved exclusively for delivery vehicles. It is typically placed at the entrance to service lanes, loading zones, or restricted access areas. What the Sign Means When a driver encounters this sign, it means only authorised delivery vehicles may use the road or portion of road beyond the sign. All other vehicles are prohibited from entering, stopping, or using the area unless specifically permitted. The key rule is: delivery vehicles only—restricted access for all other traffic. Driver Responsibilities Do not enter unless you are operating a delivery vehicle Follow all loading and unloading regulations if permitted Keep the area clear for commercial deliveries Observe any time restrictions or additional signage Where You Will See This Sign This sign is commonly found: At service entrances to shopping centres In loading bays behind commercial buildings In designated delivery zones in urban areas Near warehouses, retail stores, and business districts Purpose of the Sign The purpose of the Delivery Vehicles Only Sign is to ensure efficient access for goods transport while preventing congestion from general traffic. It helps maintain order in loading zones and ensures deliveries can be completed safely and without obstruction. Common Mistakes to Avoid Using delivery zones as parking for private vehicles Entering restricted areas without authorisation Blocking access for authorised delivery trucks Ignoring time-based delivery restrictions Safety Tips Always check signage before entering service roads Be aware of large delivery vehicles reversing or manoeuvring Use designated parking areas for private vehicles Follow all loading zone instructions carefully Penalties for Ignoring the Sign Disobeying a Delivery Vehicles Only Sign is a traffic offence and may result in: Fines Towing or clamping of vehicles Demerit points (where applicable) Obstruction penalties for blocking delivery access Summary The Delivery Vehicles Only Sign in South Africa restricts access to specific roads or zones for authorised delivery vehicles only. It ensures efficient goods distribution and prevents congestion in loading and service areas.

At the beginning of any road or part of a road.

Indicates that the road or portion of the road is set aside for use by goods vehicles.

Goods vehicles must use only this part of the roadway. No other road users may use this part of the road.

Overview The Goods Vehicles Only Sign in South Africa is a regulatory command sign used to indicate that a specific road or section of road is reserved exclusively for goods vehicles. It is typically placed at the entrance of industrial routes, freight corridors, or access roads serving commercial transport. What the Sign Means When a driver encounters this sign, it means only goods vehicles (such as trucks and freight carriers) are allowed to use the road or portion of road beyond the sign. All other types of vehicles are prohibited from entering or using the restricted section. The key rule is: goods vehicles only—no private or passenger vehicles allowed. Driver Responsibilities Do not enter unless operating a goods or freight-carrying vehicle Follow all additional access restrictions or time controls Use designated routes if you are not authorised Keep access routes clear for heavy vehicles Where You Will See This Sign This sign is commonly found: In industrial areas and freight corridors At warehouse and distribution centre access roads Near ports, depots, and logistics hubs On routes designed for heavy-duty truck traffic Purpose of the Sign The purpose of the Goods Vehicles Only Sign is to separate heavy freight traffic from general road users. It improves safety, reduces congestion, and ensures that roads designed for heavy loads are used appropriately. Common Mistakes to Avoid Entering restricted roads in a private or light vehicle Using goods-only routes as shortcuts Blocking access for freight and delivery trucks Ignoring additional access control signage Safety Tips Always check signage before entering industrial roads Be cautious of large trucks with longer stopping distances Use alternative routes if not operating a goods vehicle Stay alert in logistics zones with heavy vehicle movement Penalties for Ignoring the Sign Disobeying a Goods Vehicles Only Sign is a traffic offence and may result in: Fines Towing or removal of unauthorised vehicles Demerit points (where applicable) Obstruction of freight operations Summary The Goods Vehicles Only Sign in South Africa restricts access to certain roads for freight and heavy goods vehicles only. It helps manage traffic flow and ensures safer separation between commercial transport and general road users.

At the beginning of any road or part of a road.

Indicates that the road or a portion of the road is set aside for use by goods vehicles with a gross vehicle mass (GVM) or a gross combination mass (GCM) exceeding the mass indicated in tonnes by means of a number on such sign.

Goods vehicles over the indicated GVM must use only this part of the roadway. No other road users may use this part of the road.

Overview The Goods Vehicles Only Sign in South Africa is a regulatory command sign used to indicate that a specific road or section of road is reserved exclusively for goods vehicles. It is typically placed at the entrance of industrial routes, freight corridors, or access roads serving commercial transport. What the Sign Means When a driver encounters this sign, it means only goods vehicles (such as trucks and freight carriers) are allowed to use the road or portion of road beyond the sign. All other types of vehicles are prohibited from entering or using the restricted section. The key rule is: goods vehicles only—no private or passenger vehicles allowed. Driver Responsibilities Do not enter unless operating a goods or freight-carrying vehicle Follow all additional access restrictions or time controls Use designated routes if you are not authorised Keep access routes clear for heavy vehicles Where You Will See This Sign This sign is commonly found: In industrial areas and freight corridors At warehouse and distribution centre access roads Near ports, depots, and logistics hubs On routes designed for heavy-duty truck traffic Purpose of the Sign The purpose of the Goods Vehicles Only Sign is to separate heavy freight traffic from general road users. It improves safety, reduces congestion, and ensures that roads designed for heavy loads are used appropriately. Common Mistakes to Avoid Entering restricted roads in a private or light vehicle Using goods-only routes as shortcuts Blocking access for freight and delivery trucks Ignoring additional access control signage Safety Tips Always check signage before entering industrial roads Be cautious of large trucks with longer stopping distances Use alternative routes if not operating a goods vehicle Stay alert in logistics zones with heavy vehicle movement Penalties for Ignoring the Sign Disobeying a Goods Vehicles Only Sign is a traffic offence and may result in: Fines Towing or removal of unauthorised vehicles Demerit points (where applicable) Obstruction of freight operations Summary The Goods Vehicles Only Sign in South Africa restricts access to certain roads for freight and heavy goods vehicles only. It helps manage traffic flow and ensures safer separation between commercial transport and general road users.